SRX

 View Only

IMPORTANT MODERATION NOTICE

This community is currently under full moderation, meaning  all posts will be reviewed before appearing in the community. Please expect a brief delay—there is no need to post multiple times. If your post is rejected, you'll receive an email outlining the reason(s). We've implemented full moderation to control spam. Thank you for your patience and participation.



  • 1.  routing instance and ospf

    Posted 11-16-2016 01:54

    Hello! Trying to configure ospf on srx100 device with routing-instance enabled, everything works fine between devices without routing instance.

     

    show routing-instances 
    cifra1 {
        instance-type virtual-router;
        interface st0.0;
        interface st0.4;
        interface st0.8;
        interface vlan.1;
        routing-options {                   
            interface-routes {              
                rib-group inet cifra1;      
            }                               
            static {                        
                route 0.0.0.0/0 next-hop 212.152.36.217;
                route 172.17.0.0/16 next-hop 192.168.9.3;
                route 192.168.10.0/24 next-hop st0.8;
                route 192.168.11.0/24 next-hop st0.4;
            }                               
        }                                   
        
        protocols {                         
            ospf {                          
                rib-group cifra1;           
                area 0.0.0.0 {              
                    interface st0.4;        
                    interface st0.8;        
                    interface vlan.1;                    
                }                           
            }                               
        }                                   
    } 

    All protocols are allowed in trust zone.

     

    But

    run show ospf neighbor instance cifra1  
    

    is empty.

     

    run show ospf interface instance cifra1   
    Interface           State   Area            DR ID           BDR ID          Nbrs
    st0.4               PtToPt  0.0.0.0         0.0.0.0         0.0.0.0            0
    st0.8               PtToPt  0.0.0.0         0.0.0.0         0.0.0.0            0
    vlan.1              DR      0.0.0.0         10.12.31.1      0.0.0.0            0
    vlan.1              DR      0.0.0.0         10.12.31.1      0.0.0.0            0
    

    Any ideas why?


    #ospf
    #routinginstance


  • 2.  RE: routing instance and ospf

     
    Posted 11-17-2016 21:14

    Hello ,

     

    Can you try :

     

    > show ospf neighbor instance all

     

    If that fetch you some details . Also please provide the JUNOS version that you are running .



  • 3.  RE: routing instance and ospf

    Posted 11-17-2016 21:46

    Thank you for your reply, here it is:

    show ospf neighbor instance all 
    Instance: cifra1
    

    Btw, adjacent srx device shows (it hast routing instances:

    show ospf neighbor    
    Address          Interface              State     ID               Pri  Dead
    212.152.36.218   st0.2                  Init      192.168.2.254    128    35


  • 4.  RE: routing instance and ospf

     
    Posted 11-17-2016 22:45

    Hello ,

     

    Thanks for the output . As per the output the OSPF is stuck in init . So kindly check :

     

    1) Do we have IP on the st0 interfaces

    2) Are the interfaces in a zone and protocols OSPF allowed ?

     

    Can you share the configuration from the devices .



  • 5.  RE: routing instance and ospf

    Posted 11-17-2016 23:20

    1. No there is no IP's on st0 interfaces

    2. Yes, they are in trust zone.

     

    device with routing instance: http://pastebin.com/VQZLshnd

    device without routing instance: http://pastebin.com/eMdJ1KBQ

     

    Can you share the "show route" for the OSPF neighbors?

    ofc: here it is:

     

    device with routing instance: http://pastebin.com/XCX1RKYi

    device without: 

    Spoiler

     

    inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden)
    + = Active Route, - = Last Active, * = Both
    
    0.0.0.0/0          *[Static/5] 1w0d 22:14:12
                        > to 84.204.167.41 via fe-0/0/0.0
    84.204.167.40/29   *[Direct/0] 1w0d 22:14:12
                        > via fe-0/0/0.0
    84.204.167.45/32   *[Local/0] 1w6d 14:34:50
                          Local via fe-0/0/0.0
    172.17.20.0/24     *[Static/5] 1w0d 22:22:06
                        > via st0.2
    192.168.10.0/24    *[Direct/0] 1w4d 12:50:58
                        > via vlan.0
    192.168.10.1/32    *[Local/0] 1w6d 14:34:59
                          Local via vlan.0
    192.168.11.0/24    *[Static/5] 1d 20:26:01
                        > via st0.1
    192.168.70.0/24    *[Static/5] 1w0d 22:22:06
                        > via st0.2
    224.0.0.5/32       *[OSPF/10] 01:49:41, metric 1
                          MultiRecv
                                            
    inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
    + = Active Route, - = Last Active, * = Both
                                            
    fe80::/64          *[Direct/0] 1d 16:53:33
                        > via st0.0         
    fe80::3e61:40f:fce2:540/128             
                       *[Local/0] 1w6d 14:34:59
                          Local via st0.0  

     



  • 6.  RE: routing instance and ospf

     
    Posted 11-17-2016 23:28

    YOu need IP address on St0 interfaces to run OSPF or any dynamic routing protocols



  • 7.  RE: routing instance and ospf
    Best Answer

     
    Posted 11-17-2016 23:32

    Hello ,

     

    You need IP adress in ST interface to run any dynamic protocols . Can you configure the same and let us know the outcome .



  • 8.  RE: routing instance and ospf

     
    Posted 11-17-2016 22:51

    Can you share the "show route" for the OSPF neighbors?