Guys, I have the Juniper SRX300 in a store, we had several abrupt power outages, and when it returned to normal, my firewall went up like this.
All LEDs on and with this message.
I did the process of downloading JUNOS from the Official website and putting in a pen-drive and trying to install it but it also gave me an error.
The error follows:
_____________________________________________________________
loader> install file:///junos.tgz
Target device selected for installation: internal media
cannot open package (error 22)
loader>
____________________________________________________________________________________
________________________________________________________________________________________________________
SPI stage 1 bootloader (Build time: May 3 2016 - 23:48:30)
early_board_init: Board type: SRX_300
U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:48:31)
SRX_300 board revision major:1, minor:12, serial #: HIDDEN
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10fc00000, size: 0x400000
DRAM: 4 GiB
Clearing DRAM...... done
Using default environment
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Found valid SPI bootloader at offset: 0x90000, size: 1481840 bytes
U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:50:19)
Using DRAM size from environment: 4096 MBytes
checkboard siege
SATA0: not available
SATA1: not available
SATA BIST STATUS = 0x0
SRX_300 board revision major:1, minor:12, serial #: HIDDEN
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10f000000, size: 0x1000000
DRAM: 4 GiB
Clearing DRAM...... done
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
PCIe: Port 0 link active, 1 lanes, speed gen2
PCIe: Link timeout on port 1, probably the slot is empty
PCIe: Port 2 not in PCIe mode, skipping
Net: octeth0
Interface 0 has 1 ports (SGMII)
Type the command 'usb start' to scan for USB storage devices.
Boot Media: eUSB usb
Found TPM SLB9660 TT 1.2 by Infineon
TPM initialized
Hit any key to stop autoboot: 0
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
SF: 1048576 bytes @ 0x200000 Read: OK
## Starting application at 0x8f0000a0 ...
Consoles: U-Boot console
Found compatible API, ver. 3.1
USB1:
Starting the controller
USB XHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
USB0:
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
1 Storage Device(s) found
FreeBSD/MIPS U-Boot bootstrap loader, Revision 2.8
Memory: 4096MB
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
[2]Booting from eUSB slice 1
\
can't load '/kernel'
can't load '/kernel.old'
Press Enter to stop auto bootsequencing and to enter loader prompt.
__________________________________________________________________________________________________________________________________________________________
------------------------------
Leandro Gomes
------------------------------