Junos OS

Hello,

I have a question i have ex4200 whenever i go to cli mode i am getting following messge:

"

warning: This chassis is operating in a non-master role as part of a virtual-chassis (VC) system.
warning: Use of interactive commands should be limited to debugging and VC Port operations.
warning: Full CLI access is provided by the Virtual Chassis Master (VC-M) chassis.
warning: The VC-M can be identified through the show virtual-chassis status command executed at this console.
warning: Please logout and log into the VC-M to use CLI.

"

when i run command that show virtual-chasis status i am getting following:

"

root> show virtual-chassis status
error: the virtual-chassis-control subsystem is not running

{linecard:0}
root>

"

My configuration is as follows:

root> show configuration | display set
set system syslog user * any emergency
set system syslog file messages any notice
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set system commit factory-settings reset-chassis-lcd-menu
set system commit factory-settings reset-virtual-chassis-configuration
set interfaces ge-0/0/0 unit 0 family ethernet-switching
set interfaces ge-0/0/1 unit 0 family ethernet-switching
set interfaces ge-0/0/2 unit 0 family ethernet-switching
set interfaces ge-0/0/3 unit 0 family ethernet-switching
set interfaces ge-0/0/4 unit 0 family ethernet-switching
set interfaces ge-0/0/5 unit 0 family ethernet-switching
set interfaces ge-0/0/6 unit 0 family ethernet-switching
set interfaces ge-0/0/7 unit 0 family ethernet-switching
set interfaces ge-0/0/8 unit 0 family ethernet-switching
set interfaces ge-0/0/9 unit 0 family ethernet-switching
set interfaces ge-0/0/10 unit 0 family ethernet-switching
set interfaces ge-0/0/11 unit 0 family ethernet-switching
set interfaces ge-0/0/12 unit 0 family ethernet-switching
set interfaces ge-0/0/13 unit 0 family ethernet-switching
set interfaces ge-0/0/14 unit 0 family ethernet-switching
set interfaces ge-0/0/15 unit 0 family ethernet-switching
set interfaces ge-0/0/16 unit 0 family ethernet-switching
set interfaces ge-0/0/17 unit 0 family ethernet-switching
set interfaces ge-0/0/18 unit 0 family ethernet-switching
set interfaces ge-0/0/19 unit 0 family ethernet-switching
set interfaces ge-0/0/20 unit 0 family ethernet-switching
set interfaces ge-0/0/21 unit 0 family ethernet-switching
set interfaces ge-0/0/22 unit 0 family ethernet-switching
set interfaces ge-0/0/23 unit 0 family ethernet-switching
set interfaces ge-0/1/0 unit 0 family ethernet-switching
set interfaces xe-0/1/0 unit 0 family ethernet-switching
set interfaces ge-0/1/1 unit 0 family ethernet-switching
set interfaces xe-0/1/1 unit 0 family ethernet-switching
set interfaces ge-0/1/2 unit 0 family ethernet-switching
set interfaces xe-0/1/2 unit 0 family ethernet-switching
set interfaces ge-0/1/3 unit 0 family ethernet-switching
set protocols igmp-snooping vlan all
set protocols rstp
set protocols lldp interface all
set protocols lldp-med interface all
set ethernet-switching-options storm-control interface all
set poe interface all

THis switch is not stack switch do not ahve any other members it is stand alone. 

I would like to install new JunOS on it but only i have is console access. I do not see interfaces nor ips. 

I need help pleaseeeeeeeee......

LG

Can you do a "> request virtual-chassis reactivate"?


=====

If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.

Rebooting switch resolved this issue....

I have the same issue but it not solved by rebboot ?

Ahmad,

Is the switch a member of a virtual chassis?

Then this could be normal for a member not actiing as the RE.

If not, it might have been a member of a virtual chassis that you are now trying to use separately?

In that case zeroize and reset will likely put this in a condition you can continue to configure.

If it is some other scenario, outline what you have.