U-Boot 1.1.6 (Nov 22 2009 - 07:01:21)
Board: EX2200-24T-4G 4.11
EPLD: Version 04.091222 (0x10)
DRAM: Initializing (512MB)
Flash: 8 MB
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
ELF file is 32 bit
Consoles: U-Boot console
FreeBSD/arm U-Boot loader, Revision 1.0
(
marcelm@svl-junos-pool57.juniper.net, Wed Nov 18 14:02:39 PST 2009)
Memory: 512MB
Loading /boot/defaults/loader.conf
/kernel data=0x6d1704+0x7f924 syms=[0x4+0xc1ea0+0x4+0x99da5]
Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0x1400100 ...
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1996-2010, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 10.1R1.8 #0: 2010-02-12 16:37:10 UTC
builder@queth.juniper.net:/volume/build/junos/10.1/release/10.1R1.8/obj-
arm/bsd/sys/compile/JUNIPER-EX
CPU: Feroceon 88FR131 rev 1 (Marvell core)
WB enabled EABT branch prediction enabled
16KB/32B 4-way Instruction cache
16KB/32B 4-way write-back-locking-C Data cache
real memory = 536870912 (512 MB)
avail memory = 510271488 (486 MB)
SOC: Marvell 88F6281 rev A0, TClock 200MHz
ETHERNET SOCKET BRIDGE initialising
Initializing EXSERIES platform properties ...
mbus0: <Marvell Internal Bus (Mbus)> on motherboard
ic0: <Marvell Integrated Interrupt Controller> at mem 0xf1020200-0xf102023b on mbus0
timer0: <Marvell CPU Timer> at mem 0xf1020300-0xf102032f irq 1 on mbus0
gpio0: <Marvell Integrated GPIO Controller> at mem 0xf1010100-0xf101011f irq 35,36,37,38,39,40,41 on
mbus0
uart0: <16550 or compatible> at mem 0xf1012000-0xf101201f irq 33 on mbus0
uart0: console (9600,n,8,1)
ehci0: <88F5XXX Integrated USB 2.0 controller> at mem 0xf1050000-0xf1050fff irq 48,19 on mbus0
usb0: EHCI version 1.0
usb0 on ehci0
usb0: USB revision 2.0
uhub0: Marvell EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x04cc product 0x1520, class 9/0, rev 2.00/2.00, addr 2
uhub1: single transaction translator
uhub1: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 3
mge0: <Marvell Gigabit Ethernet controller> at mem 0xf1072000-0xf1073fff irq 12,13,14,11,46 on mbus0
mge0: hardware MAC address 2c:6b:f5:91:0b:3f
miibus0: <MII bus> on mge0
e1000phy0: <Marvell 88E1118 Gigabit PHY> on miibus0
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
i2c0: <I2C ARM 6281 OnChip i2c Controller> at mem 0xf1011000-0xf101101f irq 29 on mbus0
cfi0: <SPI flash - 8MB> at mem 0xf1010600-0xf101062f,0xf8000000-0xf87fffff irq 23 on mbus0
mpfe0: <Juniper EX-series Packet Forwarding Engine> at mem 0xf4000000-0xf7ffffff irq 113 on mbus0
pcib0: <Marvell 88F6281 PCI-Express host controller> at mem 0xf1040000-0xf1041fff,0xe8000000-0xefffffff
irq 9 on mbus0
pci0: <PCI bus> on pcib0
Initializing product: 75 ..
bme0:Virtual BME driver initializing
Timecounter "CPU Timer" frequency 200000000 Hz quality 1000
Timecounters tick every 1.000 msec
Loading the NETPFE picpeer module
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s1a
WARNING: / was not properly dismounted
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Dec 8 01:47:58 init: login_getclass: unknown class 'daemon'
cd: can't cd to /etc/db/pkg
Automatic reboot in progress...
fstab: /etc/fstab:0: No such file or DWARNING: system watchdog timer still running,
use '/sbin/watchdog -off' to disable
Enter full pathname of shell or 'recovery' for root password recovery or RETURN for /bin/sh:
NOTE: to go to multi-user operation, exit the single-user shell (with ^D)
#
#
#