Routing

 View Only

IMPORTANT MODERATION NOTICE

This community is currently under full moderation, meaning  all posts will be reviewed before appearing in the community. Please expect a brief delay—there is no need to post multiple times. If your post is rejected, you'll receive an email outlining the reason(s). We've implemented full moderation to control spam. Thank you for your patience and participation.



  • 1.  Cannot bring up interfaces between J2300 and SRX100 router.

    Posted 12-01-2013 18:29

    Hi Everyone,

     

         Maybe you guys can help me out. I am trying to bring up and interface between a J2300 and SRX100 however I am unsucessfull. Below is the configuration interface output for both the J2300 and SRX100 router. What I find weird is that I cannot see the interface Fe-0/0/0 and Fe-0/0/1 when I execute the "show interface terse" command but when I do for example "show configuration interface" I see the interfaces in the config. Thank you

     

    Physical Layout:

     

    J2300(Juniper3) Port 1 --->>>>  SRX100(Juniper1)

     

    J2300(Juniper3) Port 0 --->>>>  SRX100(Juniper2)

     

     

    Juniper3 Output:

     

     

    root@Juniper3> show interfaces terse
    Interface Admin Link Proto Local Remote
    dsc up up
    gre up up
    ipip up up
    lo0 up up
    lsi up up
    mtun up up
    pimd up up
    pime up up
    tap up up

    root@Juniper3> show configuration interfaces
    fe-0/0/0 {
    enable;
    unit 0 {
    family inet {
    address 200.10.240.1/24;
    address 20.0.0.1/24;
    address 192.168.23.3/24;
    }
    }
    }
    fe-0/0/1 {
    speed 100m;
    link-mode full-duplex;
    unit 0 {
    family inet {
    address 192.168.26.1/31;
    }
    }
    }

    root@Juniper3>

     

     

    Juniper2 Output:

     

    root@Juniper2> show interfaces terse
    Interface Admin Link Proto Local Remote
    fe-0/0/0 up up
    fe-0/0/0.0 up up
    gr-0/0/0 up up
    ip-0/0/0 up up
    lt-0/0/0 up up
    mt-0/0/0 up up
    sp-0/0/0 up up
    sp-0/0/0.0 up up inet
    sp-0/0/0.16383 up up inet 10.0.0.1 --> 10.0.0.16
    10.0.0.6 --> 0/0
    128.0.0.1 --> 128.0.1.16
    128.0.0.6 --> 0/0
    fe-0/0/1 up up
    fe-0/0/1.0 up up eth-switch
    fe-0/0/2 up down
    fe-0/0/2.0 up down eth-switch
    fe-0/0/3 up down
    fe-0/0/3.0 up down eth-switch
    fe-0/0/4 up up
    fe-0/0/4.0 up up eth-switch
    fe-0/0/5 up down
    fe-0/0/5.0 up down eth-switch
    fe-0/0/6 up down
    fe-0/0/6.0 up down eth-switch
    fe-0/0/7 up down
    fe-0/0/7.0 up down eth-switch
    gre up up
    ipip up up
    irb up up
    lo0 up up
    lo0.16384 up up inet 127.0.0.1 --> 0/0
    lo0.16385 up up inet 10.0.0.1 --> 0/0
    10.0.0.16 --> 0/0
    128.0.0.1 --> 0/0
    128.0.1.16 --> 0/0
    lo0.32768 up up
    lsi up up
    mtun up up
    pimd up up
    pime up up
    pp0 up up
    ppd0 up up
    ppe0 up up
    st0 up up
    tap up up
    vlan up up
    vlan.0 up up inet 192.168.1.1/24

    root@Juniper2> show configuration interfaces
    fe-0/0/0 {
    unit 0;
    }
    fe-0/0/1 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/2 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/3 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/4 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/5 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/6 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/7 {
    speed 100m;
    link-mode full-duplex;
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    vlan {
    unit 0 {
    family inet {
    address 192.168.1.1/24;
    }
    }
    }

    root@Juniper2>

     

     

    Juniper1 Output:

     

    root@Juniper1> show interfaces terse
    Interface Admin Link Proto Local Remote
    fe-0/0/0 up up
    fe-0/0/0.0 up up
    gr-0/0/0 up up
    ip-0/0/0 up up
    lt-0/0/0 up up
    mt-0/0/0 up up
    sp-0/0/0 up up
    sp-0/0/0.0 up up inet
    sp-0/0/0.16383 up up inet 10.0.0.1 --> 10.0.0.16
    10.0.0.6 --> 0/0
    128.0.0.1 --> 128.0.1.16
    128.0.0.6 --> 0/0
    fe-0/0/1 up up
    fe-0/0/1.0 up up eth-switch
    fe-0/0/2 up down
    fe-0/0/2.0 up down eth-switch
    fe-0/0/3 up down
    fe-0/0/3.0 up down eth-switch
    fe-0/0/4 up up
    fe-0/0/4.0 up up eth-switch
    fe-0/0/5 up down
    fe-0/0/5.0 up down eth-switch
    fe-0/0/6 up down
    fe-0/0/6.0 up down eth-switch
    fe-0/0/7 up down
    fe-0/0/7.0 up down eth-switch
    gre up up
    ipip up up
    irb up up
    lo0 up up
    lo0.16384 up up inet 127.0.0.1 --> 0/0
    lo0.16385 up up inet 10.0.0.1 --> 0/0
    10.0.0.16 --> 0/0
    128.0.0.1 --> 0/0
    128.0.0.4 --> 0/0
    128.0.1.16 --> 0/0
    lo0.32768 up up
    lsi up up
    mtun up up
    pimd up up
    pime up up
    pp0 up up
    ppd0 up up
    ppe0 up up
    st0 up up
    tap up up
    vlan up up
    vlan.0 up up inet 192.168.1.1/24

    root@Juniper1> show configuration interfaces
    fe-0/0/0 {
    unit 0;
    }
    fe-0/0/1 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/2 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/3 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/4 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/5 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/6 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    fe-0/0/7 {
    unit 0 {
    family ethernet-switching {
    vlan {
    members vlan-trust;
    }
    }
    }
    }
    vlan {
    unit 0 {
    family inet {
    address 192.168.1.1/24;
    }
    }
    }

    root@Juniper1>

     

     

     

     


    #Juniper
    #routing
    #SRX
    #router
    #J2300
    #srx100


  • 2.  RE: Cannot bring up interfaces between J2300 and SRX100 router.

    Posted 12-02-2013 05:05

    Hello there,

     


    victor.reyes.ii@citi.com wrote:

    Hi Everyone,

     

         What I find weird is that I cannot see the interface Fe-0/0/0 and Fe-0/0/1 when I execute the "show interface terse" command but when I do for example "show configuration interface" I see the interfaces in the config. Thank you

     

     

     

     



    It is well-known JUNOS feature that You can configure non-existing interfaces, then plug in the linecard+cables and it starts to work/pass traffic.

     

    On the topic - what is the J2300 exact model and JUNOS version?

    Please post the following printouts, You may wat to conceal serial numbers:

     

    show chassis hardware extensive | no-more
    show version detail | no-more

     HTH

    Thanks
    Alex



  • 3.  RE: Cannot bring up interfaces between J2300 and SRX100 router.

    Posted 12-02-2013 07:45

    Hi, When I try the first command "show chassis hardware detail | no-more" I get the message you see below. Regarding the second command below is the output. Thank you

     

     

    root@Juniper3> show chassis hardware extensive | no-more error: the chassis-control subsystem is not running

    root@Juniper3

    > show version detail | no-more Hostname: Juniper3 Model: j2300 JUNOS Software Release [7.1R1.3] (Export edition) KERNEL 7.1R1.3 #0 built by builder on 2005-02-11 04:47:41 UTC MGD release 7.1R1.3 built by builder on 2005-02-11 04:34:51 UTC CLI release 7.1R1.3 built by builder on 2005-02-11 04:34:36 UTC CHASSISD release 7.1R1.3 built by builder on 2005-02-11 04:19:15 UTC DFWD release 7.1R1.3 built by builder on 2005-02-11 04:21:38 UTC DCD release 7.1R1.3 built by builder on 2005-02-11 04:17:04 UTC RPD release 7.1R1.3 built by builder on 2005-02-11 04:35:03 UTC SNMPD release 7.1R1.3 built by builder on 2005-02-11 04:26:03 UTC MIB2D release 7.1R1.3 built by builder on 2005-02-11 04:23:45 UTC VRRPD release 7.1R1.3 built by builder on 2005-02-11 04:26:47 UTC ALARMD release 7.1R1.3 built by builder on 2005-02-11 04:18:56 UTC PFED release 7.1R1.3 built by builder on 2005-02-11 04:25:04 UTC CRAFTD release 7.1R1.3 built by builder on 2005-02-11 04:21:25 UTC SAMPLED release 7.1R1.3 built by builder on 2005-02-11 04:25:43 UTC RMOPD release 7.1R1.3 built by builder on 2005-02-11 04:25:25 UTC COSD release 7.1R1.3 built by builder on 2005-02-11 04:21:09 UTC KMD release 7.1R1.3 built by builder on 2005-02-11 04:51:42 UTC NASD release 7.1R1.3 built by builder on 2005-02-11 04:24:58 UTC FUD release 7.1R1.3 built by builder on 2005-02-11 04:21:56 UTC PPMD release 7.1R1.3 built by builder on 2005-02-11 04:35:00 UTC SPD release 7.1R1.3 built by builder on 2005-02-11 04:26:27 UTC PGMD release 7.1R1.3 built by builder on 2005-02-11 04:34:57 UTC BFDD release 7.1R1.3 built by builder on 2005-02-11 04:34:33 UTC HTTPD release 7.1R1.3 built by builder on 2005-02-11 04:51:40 UTC AUTOD release 7.1R1.3 built by builder on 2005-02-11 04:47:45 UTC FWDD release 7.1R1.3 built by builder on 2005-02-11 04:52:29 UTC SDXD release 7.1R1.3 built by builder on 2005-02-11 04:39:50 UTC DHCPD release 7.1R1.3 built by builder on 2005-02-11 04:47:56 UTC USBD release 7.1R1.3 built by builder on 2005-02-11 04:48:05 UTC PPPOED release 7.1R1.3 built by builder on 2005-02-11 04:25:19 UTC jkernel-dd release 7.1R1.3 built by builder on 2005-02-11 04:08:53 UTC jroute-dd release 7.1R1.3 built by builder on 2005-02-11 04:09:28 UTC jcrypto-dd release 7.1R1.3 built by builder on 2005-02-11 04:10:05 UTC

    root@Juniper3

    >



  • 4.  RE: Cannot bring up interfaces between J2300 and SRX100 router.
    Best Answer

    Posted 12-02-2013 14:13

    Hello,

     

    The issue is with Chassisd:

     

    root@Juniper3> show chassis hardware extensive | no-more error: the chassis-control subsystem is not running

     You may wish to try:

     

    restart chassis-control

     Failing that, a reboot. 

    If the issue persists after reboot, upgrade Your JUNOS - You may get older J2300-compatible code through JTAC if You have a support contract.

    HTH

    Thanks

    Alex



  • 5.  RE: Cannot bring up interfaces between J2300 and SRX100 router.

    Posted 12-02-2013 18:53

    Thank you I rebooted the router again the and chassis control daemon started again. Thank you