Routing

 View Only

IMPORTANT MODERATION NOTICE

This community is currently under full moderation, meaning  all posts will be reviewed before appearing in the community. Please expect a brief delay—there is no need to post multiple times. If your post is rejected, you'll receive an email outlining the reason(s). We've implemented full moderation to control spam. Thank you for your patience and participation.



  • 1.  MX80 - Format nand1

    Posted 05-24-2022 05:56
    One of our MX80 routers appears to have a bad sector in nand1 (da1). Over the past 3 months it has locked up twice after displaying this message on the console.
    g_vfs_done():da1s1a[WRITE(offset=8192, length=2048)]error = 5​


    The nand1 device (da1) is recognized at boot and the da1s1a partition completes fsck normally.

    root@edge1% dmesg|grep da1
    da1 at umass-sim1 bus 1 target 0 lun 0
    da1: <ATP ATP IG eUSB 1100> Fixed Direct Access SCSI-4 device
    da1: 40.000MB/s transfers
    da1: 3838MB (7860224 512 byte sectors: 255H 63S/T 489C)
    
    root@edge1% fsck /dev/da1s1a
    ** /dev/da1s1a
    ** Last Mounted on /mnt
    ** Phase 1 - Check Blocks and Sizes
    ** Phase 2 - Check Pathnames
    ** Phase 3 - Check Connectivity
    ** Phase 4 - Check Reference Counts
    ** Phase 5 - Check Cyl groups
    1051 files, 15444 used, 437748 free (44 frags, 54713 blocks, 0.0% fragmentation)

    Router is running JUNOS 20.4R3.8. Is there a utility on the JUNOS MX distribution to low level format a nand device (similar to nand-mediack on other JUNOS platforms)?  A low level format should remap any bad sectors.

    Else, can a USB flash drive be used for /altroot, /altconfig and /var (e.g. to substitute nand1)? This MX80 is scheduled to be replaced around the end of the year, but should be operational until then.

    Thanks.

    ------------------------------
    JAlvarez
    ------------------------------


  • 2.  RE: MX80 - Format nand1

    Posted 29 days ago
    Couldn't find a low level format procedure for MX80 nand. Yet replacing nand1 with a USB flash drive is feasible with these steps:

    1. Create a snapshot on a USB drive. Example uses a SanDisk 8GB drive. Most 4 to 32GB drives should work with an MX80 running JUNOS 20.4R3.8.
    root@edge1> request system snapshot media usb partition
    Clearing current label...
    Partitioning usb media (da2) ...
    Doing the initial labeling...
    Partitions on snapshot:
    
      Partition  Mountpoint  Size    Snapshot argument
          a      /           637MB   root-size
          e      /config     101MB   config-size
          f      /var        6GB     var-size
    Running newfs (637MB) on usb media  / partition (da2s1a)...
    Running newfs (101MB) on usb media  /config partition (da2s1e)...
    Running newfs (6GB) on usb media  /var partition (da2s1f)...
    Copying '/dev/da0s1a' to '/dev/da2s1a' .. (this may take a few minutes)
    Copying '/dev/da0s1e' to '/dev/da2s1e' .. (this may take a few minutes)
    The following filesystems were archived: / /config
    root@edge1>​

    2. Change/etc/fstab entries from nand1 (da1) to USB (da2). Commented out da1s1b partitions (/tmp, /mfs) since the snapshot didn't create a da2s1b partition. Without dedicated partitions, those directories will become part of the root filesystem (/dev/da0s1a).
    # Device       Mountpoint  FStype  Options  Dump  Pass#
    /dev/da0s1a    /           ufs     rw        1    1
    /dev/da0s1e    /config     ufs     rw        2    2
    proc           /proc       procfs  rw        0    0
    /dev/da2s1f    /var        ufs     rw,noauto 2    2
    /dev/da0s1b    none       swap    sw        0    0
    #/dev/da1s1b    /tmp        mfs     rw,noauto 0    0
    #/dev/da1s1b    /mfs        mfs     rw,noauto 0    0
    /dev/da2s1a    /altroot    ufs     rw,noauto 2    0
    /dev/da2s1e    /altconfig  ufs     rw,noauto 2    0​


    3. Change boot order to only nand-flash0. Intent was to use nand-flash0,usb (USB last) but it kept changing to usb,nand-flash0 (USB first).

    root@edge1% sysctl -a | grep bootdev
    machdep.currbootdev: nand-flash0
    machdep.nextbootdev: usb
    machdep.bootdevs: usb,nand-flash0,nand-flash1
    
    root@core1% sysctl -w machdep.bootdevs=nand-flash0
    machdep.bootdevs: usb,nand-flash0,nand-flash1 -> nand-flash0
    
    root@core1% sysctl -a | grep bootdev
    machdep.currbootdev: nand-flash0
    machdep.nextbootdev: usb
    machdep.bootdevs: nand-flash0​


    4. Reboot.



    ------------------------------
    JAlvarez
    ------------------------------