I really appreciate your prompt response and detail procedure to install Junos.
From the log, I was able to see, Junos-srxsme-15.1X49-D60.7-domestic.tgz is there on device and hence I tried to use same package to install using USB and TFTP server.
Every time, SRX 300 starts installation and get stuck at below line. and then device goes to db> prompt.
none of the time, installation finishes completely. Is any other release need to try e.g.19.1?
One more observation is that when device boots from eUSB slice 2 , it gets kernel and ends up with same error cpu:0..., but if boots from other slice such as 1,3,4, device gives message can't load /Kernel.
i welcome all experts on this community for suggestion to fix the issue.
Original Message:
Sent: 06-10-2023 05:58
From: spuluka
Subject: srx300 ENDS UP IN cpu:0-Trap cause = 3 (TLB miss (store) - kernel mode) AFTER REBOOT
The Junos installation is corrupt or there is a hardware issue. You can attempt to get a fresh install of Junos if you can get to a loader prompt using this.
https://www.juniper.net/documentation/software/junos-security/junos-security10.2/junos-security-admin-guide/topic-installing-software-boot-loader-usb.html
If you are having trouble getting a clean loader prompt more options are listed in this kb.
https://www.juniper.net/documentation/software/junos-security/junos-security10.2/junos-security-admin-guide/section-srx-series-tftp-loader.html#topic-accessing-uboot-prompt
------------------------------
Steve Puluka BSEET - Juniper Ambassador
IP Architect - DQE Communications Pittsburgh, PA (Metro Ethernet & ISP - Retired)
http://puluka.com/home
Original Message:
Sent: 06-09-2023 15:08
From: PRACHI GADEKAR
Subject: srx300 ENDS UP IN cpu:0-Trap cause = 3 (TLB miss (store) - kernel mode) AFTER REBOOT
Hi All,
My SRX300 all the time goes in Panic. unable to get CLI or SHELL command mode.
below is log details.
loader> reboot
Resetting...
SPI stage 1 bootloader (Build time: May 3 2016 - 23:48:30)
early_board_init: Board type: SRX_300
U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:48:31)
SRX_300 board revision major:1, minor:12, serial #: CV2918AF0150
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10fc00000, size: 0x400000
DRAM: 4 GiB
Clearing DRAM...... done
Using default environment
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
Found valid SPI bootloader at offset: 0x90000, size: 1481840 bytes
U-Boot 2013.07-JNPR-3.1 (Build time: May 03 2016 - 23:50:19)
Using DRAM size from environment: 4096 MBytes
checkboard siege
SATA0: not available
SATA1: not available
SATA BIST STATUS = 0x0
SRX_300 board revision major:1, minor:12, serial #: CV2918AF0150
OCTEON CN7020-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 600 MHz, DDR clock: 667 MHz (1334 Mhz DDR)
Base DRAM address used by u-boot: 0x10f000000, size: 0x1000000
DRAM: 4 GiB
Clearing DRAM...... done
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
PCIe: Port 0 link active, 1 lanes, speed gen2
PCIe: Link timeout on port 1, probably the slot is empty
PCIe: Port 2 not in PCIe mode, skipping
Net: octeth0
Interface 0 has 1 ports (SGMII)
Type the command 'usb start' to scan for USB storage devices.
Boot Media: eUSB usb
Found TPM SLB9660 TT 1.2 by Infineon
TPM initialized
Hit any key to stop autoboot: 0
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
SF: 1048576 bytes @ 0x200000 Read: OK
## Starting application at 0x8f0000a0 ...
Consoles: U-Boot console
Found compatible API, ver. 3.1
USB1:
Starting the controller
USB XHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
USB0:
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
FreeBSD/MIPS U-Boot bootstrap loader, Revision 2.11
(builder@monarth, Sun Jul 26 18:59:02 PDT 2020)
Memory: 4096MB
SF: Detected MX25L6405D with page size 256 Bytes, erase size 64 KiB, total 8 MiB
[12]Booting from eUSB slice 2
Loading /boot/defaults/loader.conf
/kernel data=0xb817f4+0x151638 syms=[0x4+0x9de30+0x4+0xeb463]
Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0x801000c0 ...
init regular console
Primary ICache: Sets 16 Size 128 Asso 39
Primary DCache: Sets 8 Size 128 Asso 32
Secondary DCache: Sets 1024 Size 128 Asso 4
CIU_FUSE 0x3/0x3
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
kld_map_v: 0x8ff80000, kld_map_p: 0x0
Running in PARTITIONED TLB MODE
Copyright (c) 1996-2016, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
JUNOS 15.1X49-D60.7 #0: 2016-09-13 22:27:47 UTC
builder@svl-junos-p003:/volume/build/junos/15.1/service/15.1X49-D60.7/obj/octeon/junos/bsd/kernels/JSRXNLE/kernel
can't re-use a leaf (debug)!
JUNOS 15.1X49-D60.7 #0: 2016-09-13 22:27:47 UTC
builder@svl-junos-p003:/volume/build/junos/15.1/service/15.1X49-D60.7/obj/octeon/junos/bsd/kernels/JSRXNLE/kernel
real memory = 4294967296 (4194304K bytes)
avail memory = 2621882368 (2500MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
Security policy loaded: JUNOS MAC/runasnonroot (mac_runasnonroot)
Security policy loaded: Junos MAC/veriexec (mac_veriexec)
Security policy loaded: JUNOS MAC/pcap (mac_pcap)
MAC/veriexec fingerprint module loaded: SHA256
MAC/veriexec fingerprint module loaded: SHA1
netisr_init: !debug_mpsafenet, forcing maxthreads from 2 to 1
cpu0 on motherboard
: CAVIUM's OCTEON 70XX/71XX CPU Rev. 0.2 with no FPU implemented
L1 Cache: I size 78kb(128 line), D size 32kb(128 line), thirty two way.
L2 Cache: Size 512kb, 4 way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
set clock 0x58
xhci0: <Cavium Octeon 7xxx xHCI Host Driver> on obio0
usb0: <USB bus for xHCI Controller> on xhci0
usb0: USB revision 3.0
uhub0: vendor 0x0000 XHCI root hub, class 9/0, rev 3.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
xhci1: <Cavium Octeon 7xxx xHCI Host Driver> on obio0
usb1: <USB bus for xHCI Controller> on xhci1
usb1: USB revision 3.0
uhub1: vendor 0x0000 XHCI root hub, class 9/0, rev 3.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
cpld0 on obio0
pcib0: <Cavium on-chip PCIe HOST bridge> on obio0
Disabling Octeon big bar support
pcib0: Initialized controller
pci0: <PCI bus> on pcib0
pci0: <network, ethernet> at device 0.0 (no driver attached)
pci0: <network, ethernet> at device 0.1 (no driver attached)
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <Macronix MX25L64 - 8MB> on obio0
cfi1: <Macronix MX25L64 - 8MB> on obio0
umass0: ATP Electronics ATP CG eUSB, rev 2.00/11.00, addr 2
Timecounter "mips" frequency 1200000000 Hz quality 0
Registered AMT tunnel Encap with UDP Tunnel!
Loading Redundant LT driver
###PCB Group initialized for udppcbgroup
###PCB Group initialized for tcppcbgroup
Kernel thread "wkupdaemon" (pid 47) exited prematurely.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ATP ATP CG eUSB 1100> Fixed Direct Access SCSI-4 device
da0: 40.000MB/s transfers
da0: 7672MB (15712256 512 byte sectors: 255H 63S/T 978C)
Trying to mount root from ufs:/dev/da0s2a
WARNING: / was not properly dismounted
MFSINIT: Initialising MFSROOT
WARNING: / was not properly dismounted
Ignoring watchdog timeout during boot/reboot
Ignoring watchdog timeout during boot/reboot
xhci_process_cmd_event+0x124 (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x801891bc sz 64
xhci_scan_ring_event+0xd8 (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x80189b40 sz 64
xhci_intr+0x2a0 (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x8077771c sz 32
mips_handle_this_interrupt+0x8c (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x807777a8 sz 40
mips_handle_interrupts+0x58 (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x80777bcc sz 48
mips_interrupt+0x224 (0xc6e3d400,0xc6ee6020,0x28901902,0x13c0301) ra 0x80a58214 sz 32
MipsKernIntr+0x140 (0x80b20000,0x80d9ffe0,0xffff8010,0x7d) ra 0x8077562c sz 368
cpu_idle+0x10 (0x80b20000,0x80d9ffe0,0xffff8010,0x7d) ra 0x801e6054 sz 24
idle_proc+0x118 (0x80b20000,0x80d9ffe0,0xffff8010,0x7d) ra 0x801e47c8 sz 40
fork_exit+0x230 (0x80b20000,0x80d9ffe0,0xffff8010,0x7d) ra 0x80a58ea0 sz 40
MipsNMIException+0x34 (0x80b20000,0x80d9ffe0,0xffff8010,0x7d) ra 0 sz 0
pid 21, process: idle: cpu0
cpu:0-Trap cause = 3 (TLB miss (store) - kernel mode)
badvaddr = 0x1010, pc = 0x80187fd4, ra = 0x801891bc, sr = 0x508008a3
[thread pid 21 tid 100009 ]
Stopped at xhci_process_cmd_event+0x124: sw zero,16(s0)
db>
Appreciate your help on this.
------------------------------
PRACHI GADEKAR
------------------------------