Sorry, I forgot this detail.
Here is my routing table. I get the neighbor by OSPF
show route
inet.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
186.237.112.16/28 *[Direct/0] 15:08:37
> via irb.100
186.237.112.30/32 *[Local/0] 15:08:37
Local via irb.100
VS-IDC.inet.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
1.1.1.1/32 *[Direct/0] 15:10:28
> via lo0.0
172.17.1.0/24 *[Direct/0] 15:08:37
> via ge-0/0/0.4050
172.17.1.106/32 *[Local/0] 15:08:37
Local via ge-0/0/0.4050
224.0.0.2/32 *[LDP/9] 15:10:28, metric 1
MultiRecv
224.0.0.5/32 *[OSPF/10] 15:10:36, metric 1
MultiRecv
VS-IDC.mpls.0: 6 destinations, 6 routes (6 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
0 *[MPLS/0] 15:10:36, metric 1
to table VS-IDC.inet.0
0(S=0) *[MPLS/0] 15:10:36, metric 1
to table VS-IDC.mpls.0
1 *[MPLS/0] 15:10:36, metric 1
Receive
2 *[MPLS/0] 15:10:36, metric 1
to table VS-IDC.inet6.0
2(S=0) *[MPLS/0] 15:10:36, metric 1
to table VS-IDC.mpls.0
13 *[MPLS/0] 15:10:36, metric 1
Receive
inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
ff02::2/128 *[INET6/0] 15:10:36
MultiRecv
VS-IDC.inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
ff02::2/128 *[INET6/0] 15:10:36
MultiRecv
l2circuit.0: 1 destinations, 1 routes (0 active, 0 holddown, 1 hidden)
------------------------------
Guilherme Noll
------------------------------
Original Message:
Sent: 09-28-2022 19:06
From: STEVE PULUKA
Subject: Problem to use labels of other routing-instance in VPLS connection
Where is the vpls neighbor on the network?
The configuration above would only work with two directly connected devices if there is anything between the two vpls neighbors you will also need to configure an LSP and expand to targeted LDP signaling.
------------------------------
Steve Puluka BSEET - Juniper Ambassador
IP Architect - DQE Communications Pittsburgh, PA (Metro Ethernet & ISP - Retired)
http://puluka.com/home
Original Message:
Sent: 09-28-2022 10:29
From: Guilherme Noll
Subject: Problem to use labels of other routing-instance in VPLS connection
Hello friends,
I have a scenario with a VPLS where I would need to use the labels and ips from another table (not the master) and I'm having difficulty.
Follow my current configuration
set interfaces ge-0/0/0 flexible-vlan-tagging
set interfaces ge-0/0/0 encapsulation flexible-ethernet-services
set interfaces ge-0/0/0 unit 3904 encapsulation vlan-vpls
set interfaces ge-0/0/0 unit 3904 vlan-id 100
set interfaces ge-0/0/0 unit 4050 vlan-id 4050
set interfaces ge-0/0/0 unit 4050 family inet address 172.17.1.106/24
set interfaces ge-0/0/0 unit 4050 family mpls mtu 1450
set interfaces irb unit 100 family inet address 192.168.1.1/24
set interfaces lo0 unit 0 family inet address 1.1.1.1/32
set routing-instances VS-IDC protocols ospf area 0.0.0.1 interface ge-0/0/0.4050 interface-type p2p
set routing-instances VS-IDC protocols ospf area 0.0.0.1 interface lo0.0 passive
set routing-instances VS-IDC protocols ldp interface ge-0/0/0.4050
set routing-instances VS-IDC protocols ldp interface lo0.0
set routing-instances VS-IDC protocols mpls interface ge-0/0/0.4050
set routing-instances VS-IDC protocols mpls interface lo0.0
set routing-instances VS-IDC instance-type virtual-router
set routing-instances VS-IDC interface ge-0/0/0.4050
set routing-instances VS-IDC interface lo0.0
set routing-instances vpls protocols vpls encapsulation-type ethernet
set routing-instances vpls protocols vpls no-tunnel-services
set routing-instances vpls protocols vpls vpls-id 3904
set routing-instances vpls protocols vpls mtu 1508
set routing-instances vpls protocols vpls neighbor 2.2.2.2
set routing-instances vpls instance-type vpls
set routing-instances vpls vlan-id 100
set routing-instances vpls routing-interface irb.100
set routing-instances vpls interface ge-0/0/0.3904
set routing-options router-id 1.1.1.1
the show vpls connections command returns the VPLS error as being OL (no outgoing label)
Would there be any way to use the labels generated in the routing-instance VS-IDC in the VPLS?
------------------------------
Guilherme Noll
------------------------------