Routing

 View Only
last person joined: 2 days ago 

Ask questions and share experiences about ACX Series, CTP Series, MX Series, PTX Series, SSR Series, JRR Series, and all things routing, including portfolios and protocols.

If you have a question or a use case, likely there are others who are experiencing or worked through the same thing. Don't hesitate to jump in and ask or share your knowledge! Post here or in the vMX community. 

Need additional guidance?  Check out these Juniper Resources.

Documentation Technical Bulletins Knowledge Base Day One Books

Latest Discussion Posts

  • Profile Picture

    RE: L3Vpn No comming up

    By: Flashover_ , 9 minutes ago

    I think I made a mistake when I asked for the previous output :) Can you perform: show route table CustA We should see: protocol [direct + local] for your ge000 interface OSPF loopback learned across ge000 BGP route from the other ...

  • Profile Picture

    RE: L3Vpn No comming up

    By: DAVID CRIOLLO , 41 minutes ago

    Changes did not work either. I have attached requested information. Thanks in advaces R11 root@R11# run show route advertising-protocol bgp 10.255.255.33 root@R11# run show route receive-protocol bgp 10.255.255.33 inet.0: 19 ...

  • Profile Picture

    RE: L3Vpn No comming up

    By: Flashover_ , an hour ago

    Can you add the following: set policy-options policy-statement ACCEPT term 1 from protocol bgp set policy-options policy-statement ACCEPT term 1 then accept And to verify: On R11, what is shared with/from neighbors? show route advertising-protocol ...

  • Profile Picture

    RE: L3Vpn No comming up

    By: DAVID CRIOLLO , an hour ago

    I added it to the PE routers and It did not worked. Something is preventing the route to be scattered. I remember building it in Cisco, but I'm having issues with Juniper ------------------------------ DAVID CRIOLLO ------------------------------

  • Profile Picture

    RE: L3Vpn No comming up

    By: Flashover_ , 4 hours ago

    Hi David Can you add the following to the configuration: set protocols bgp group IBGP family inet-vpn unicast I think it's missing from your BGP core configuration. Please check if other families are needed there too. By default only inet-unicast ...

  • Profile Picture

    L3Vpn No comming up

    By: DAVID CRIOLLO , 4 hours ago

    Hi Everyone, I'm building a L3vpn between these two MX routers, the OSPF adjacency is up between MW and CPEs, however. no routes are been shared. Attached configuration from both PE root@R11# show | display set set version 20191026.124700_builder.r1063854 ...

  • Profile Picture

    EVPN MPLS Confusion

    By: Fredrick Lowery , 5 days ago

    Looking for recommendations on which EVPN instance type I should be considering. I'm supporting the build-out of an SR-MPLS network and we have decided to move to EVPN for customer layer2 E-line and E-Lan requirements. We are excited about using EVPN ...

Announcements

  • Introducing Juniper Support Portal (JSP) Mobile App for iOS

    The Juniper Support Portal (JSP) Mobile App is now available for customer use on iOS platforms. The app is designed to provide mobile access for on-the-go service support. 

    What’s available?

    • Live Chat Support
    • Instant Notifications
    • Knowledge Base Access 

Unanswered Posts

  • EVPN MPLS Confusion

  • Inter-AS SRv6 on an ASBR that is also a PE...

  • Which is the best method to make fast failover RSVP ...

  • What feature in Juniper QFX5120 that similar with split-horizon ...

  • Event-script not work in vJunos-Router?

  • H-VPLS Hub-And-Spoke Model same to which model of ...

  • MS-MPC UDP Flood

Top Contributors in the Community