Routing

 View Only
last person joined: yesterday 

Ask questions and share experiences about ACX Series, CTP Series, MX Series, PTX Series, SSR Series, JRR Series, and all things routing, including portfolios and protocols.

If you have a question or a use case, likely there are others who are experiencing or worked through the same thing. Don't hesitate to jump in and ask or share your knowledge! Post here or in the vMX community. 

Need additional guidance?  Check out these Juniper Resources.

Technical Bulletins Knowledge BaseDay One+

Latest Discussion Posts

  • Profile Picture

    RE: VPN site-to-site (Unifi Dream Machine to Juniper ...

    By: spuluka , yesterday

    For ipsec vpn with the remote site on a dynamic ip address you will need to use aggressive mode and host id instead of gateway ip address. The kb outlining the SRX side configuration for that is here in the knowledge base. You will need to find the ...

  • Profile Picture

    RE: VPN site-to-site (Unifi Dream Machine to Juniper ...

    By: fb35523 , yesterday

    Yes, they can do IPsec between each other. The "DreamMachine" is more of a NightmareMachine in my eyes, but when one of those failed to connect to a Palo, the SRX succeeded. In that particular case, the DreamMachine was replaced with a spare and then ...

  • Profile Picture

    RE: BT FTTP broadband (UK) with SRX. inproperly fu ...

    By: ARENTAS BUTKUS , 2 days ago

    Thank you for your time replying to me. Yes..... It could be MTU problem. I have a suggestion from someone to delete interfaces pp0 unit 0 family inet mtu 1492 set interfaces pp0 unit 0 pppoe-options ppp-max-payload 1500 I can't confirm that ...

  • Profile Picture

    RE: BT FTTP broadband (UK) with SRX. inproperly fu ...

    By: markw , 2 days ago

    Looking at the symptoms I am almost entirely certain this is an MTU issue. I see it uses PPPoE and that reinforces this suspicion, because that is essentially a sort of tunneling technology, meaning there is a PPP encapsulation of your packets and you ...

  • Profile Picture

    VPN site-to-site (Unifi Dream Machine to Juniper S ...

    By: Leetrix , 3 days ago

    Hello everyone, everything good ? I would like to know if it is possible to close a site-to-site VPN between a Unifi Dream Machine and a Juniper srx 345. Remembering that at the Unifi Dream Machine location I do not have internet with a fixed IP, the ...

  • Profile Picture

    BT FTTP broadband (UK) with SRX. inproperly functi ...

    By: ARENTAS BUTKUS , 4 days ago

    BT FTTP broadband (UK) with SRX - mistic. Hello, I recently changed home broadband to BT which they call "full-fibre" FTTP. I used SRX as an ISP router with the previous provider with the VDSL2-A interfaces, Now simply I have to plug in the ethernet ...

  • Profile Picture

    MX10003 diagnostic optic log: RX power low warning|alarm ...

    By: M , 6 days ago

    Hi all, on Juniper MX10003 with Junos: 21.4R3-S2.3, I have a 100G juniper original optic that receive an alarm due to connectivity issue (fiber issue). It started to fill the logs with the alarms set and cleared: Sep 28 23:36:56.954 ...

Announcements

Unanswered Posts

  • MX10003 diagnostic optic log: RX power low warning|alarm ...

  • Interprovider Layer 3 VPN Option A

  • BGP OVER IPSEC SOLUTION WITH AWS AND SRX5800

  • PACKET LOSS ON A SECURE TUNNEL P2P IP ( JUNIPER AND ...

  • MPLS L3VPN TTL problem

  • Question on Segment Routing Shared Fate Groups

  • Question on Segment Routing L-OSPF Route Protocol ...

Top Contributors in the Community