SRX

Expand all | Collapse all

SRX 1500 Clustering

Jump to Best Answer
  • 1.  SRX 1500 Clustering

    Posted 06-27-2016 02:41

    Hi all , 

    i did not find anything about how to configure HA on SRX 1500 .

    Help .


    Thank you

    🙂



  • 2.  RE: SRX 1500 Clustering
    Best Answer

    Posted 06-27-2016 03:34


  • 3.  RE: SRX 1500 Clustering

     
    Posted 06-27-2016 03:42

    Despite the numbering system, the new SRX1500 is not quite branch and not quite high end DC.  These are the instructions for chassis cluster on the SRX1500; SRX550 and vSRX models.

     

    https://www.juniper.net/techpubs/en_US/junos15.1x49-d30/topics/example/chassis-cluster-active-passive-pair-configuring-cli.html



  • 4.  RE: SRX 1500 Clustering

    Posted 07-04-2016 00:55

    Your help is appreciated 🙂



  • 5.  RE: SRX 1500 Clustering

    Posted 06-27-2016 03:51

    Hi Wael,

     

     

    To configure chassis cluster for SRX 1500 you can follow the same procedure as used for the SRX 1400. There is not much difference as far as configuration is considered to have chassis cluster for SRX 1500 in comparison to SRX 1400.

     

    On the hardware level there is a dedicated control port on SRX 1500 to be used for control link. Also it cannot be configured like on SRX 1400 as well but it needs to be connected while configuring cluster on SRX 1500.

     

    Thanks,
    Pulkit Bhandari

    Please mark my response as Solution Accepted if it Helps, Kudos are Appreciated too. Smiley Happy



  • 6.  RE: SRX 1500 Clustering

    Posted 06-27-2016 05:54

    Hi Wael,

     

     

    SRX1500 devices use dedicated control ports.

    And for fabric link connection must be any pair of either Gigabit Ethernet or 10-Gigabit Ethernet interfaces on all SRX Series devices.

    http://www.juniper.net/techpubs/en_US/junos15.1x49-d40/topics/task/operational/chassis-cluster-srx-series-hardware-connecting.html

     



  • 7.  RE: SRX 1500 Clustering

    Posted 07-04-2016 00:55

    Thank you 



  • 8.  RE: SRX 1500 Clustering

    Posted 08-10-2016 02:12

    Hi - 

     

    could you tell me if it's possible to have dual control links at the SRX1500?

     

    thank you

     

    Markus



  • 9.  RE: SRX 1500 Clustering

    Posted 08-10-2016 06:57

    Hello Markus,

     

     

    SRX 1500 uses dedicated control ports and it cannot be configured and there is only one port for HA control link on SRX 1500 so dual control links is not possible on SRX 1500.

     

    Thanks,
    Pulkit Bhandari
    Please mark my response as Solution Accepted if it Helps, Kudos are Appreciated too. 🙂



  • 10.  RE: SRX 1500 Clustering

    Posted 07-08-2016 14:54

    Does the HA control link for SRX 1500 have to be fiber?  I am staging a pair with copper SFPs and looks like both nodes are sending heartbeats but not receiving:

     

    root> show interfaces em0 extensive
    Physical interface: em0 , Enabled, Physical link is Up
    Interface index: 8, SNMP ifIndex: 17, Generation: 1
    Type: Ethernet, Link-level type: Ethernet, MTU: 1514, Clocking: Unspecified,
    Speed: 1000mbps
    Device flags : Present Running
    Interface flags: SNMP-Traps
    Link type : Full-Duplex
    Physical info : Unspecified
    Hold-times : Up 0 ms, Down 0 ms
    Current address: 02:00:00:01:01:04, Hardware address: 02:00:00:01:01:04
    Alternate link address: Unspecified
    Last flapped : Never
    Statistics last cleared: Never
    Traffic statistics:
    Input bytes : 0
    Output bytes : 0
    Input packets: 67167
    Output packets: 75284
    Input errors:
    Errors: 0, Drops: 0, Framing errors: 0, Runts: 0, Giants: 0,
    Policed discards: 0, Resource errors: 0
    Output errors:
    Carrier transitions: 0, Errors: 0, Drops: 0, MTU errors: 0,
    Resource errors: 0

     

    root> show chassis cluster statistics
    Control link statistics:
    Control link 0:
    Heartbeat packets sent: 3288
    Heartbeat packets received: 0
    Heartbeat packet errors: 0
    Fabric link statistics:
    Child link 0
    Probes sent: 0
    Probes received: 0
    Child link 1
    Probes sent: 0
    Probes received: 0

     

    root> show chassis cluster interfaces
    Control link status: Down

    Control interfaces:
    Index Interface Monitored-Status Internal-SA
    0 em0 Down Disabled

    Fabric link status: Down

    Fabric interfaces:
    Name Child-interface Status
    (Physical/Monitored)
    fab0
    fab0

    Redundant-pseudo-interface Information:
    Name Status Redundancy-group
    lo0 Up 0

    {primary:node0}

     


    root> show chassis cluster information
    node0:
    --------------------------------------------------------------------------
    Redundancy Group Information:

    Redundancy Group 0 , Current State: primary, Weight: 255

    Time From To Reason
    Jul 8 20:56:30 hold secondary Hold timer expired
    Jul 8 20:56:46 secondary primary Only node present

    Chassis cluster LED information:
    Current LED color: Red
    Last LED change reason: Peer node: node1 is not present

    Failure Information:

    Control-link Failure Information:
    Link Status: Monitor Failed
    Dual Control Link Status: Unsupported

    Interface Physical / Monitored Status
    em0 Up / Down



  • 11.  RE: SRX 1500 Clustering

     
    Posted 07-09-2016 08:37

    Do you have the fabric link also configured and cabled?

     

    Do you have a cross over cable on your copper port control links?