Junos OS

Expand all | Collapse all

POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

  • 1.  POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Posted 05-20-2021 11:36


    When applying the policy it does not work


    XXXXX@XXXXXE01> show configuration interfaces ae1.773
    description "XXXXXXXX";
    vlan-id 773;
    family inet {
    policer {
    input FP-LIMIT-25M;
    output FP-LIMIT-55M;
    }
    address XX.XX.XX.XX/30;


    there is not pilicer in the interface ae1.773


    XXXX@XXXXE01> show policer | match 773
    FP-LIMIT-3M-ge-11/2/6.2712-inet-i 3769773 2559
    FP-LIMIT-1M-ge-1/2/5.795-inet-o 210773671 3394322
    FP-LIMIT-11M-ae1.772-inet-o 5777336586 3872372
    FP-LIMIT-10M-ge-11/2/7.533-inet-o 6093777314 4448029
    FP-LIMIT-10M-ge-11/2/7.2033-inet-i 10457194639 7731254
    FP-LIMIT-3M-ae0.2064-inet-o 117356170773 82924606

    {master}


    Please your help




    ------------------------------
    Juan Gutierrez Cunalata
    ------------------------------


  • 2.  RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

     
    Posted 05-20-2021 12:44

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-two-color-bandwidth.html

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     


    Juniper Business Use Only






  • 3.  RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Posted 05-20-2021 13:24

    Hi –R

     

     

    The problem is also seen in that the policy applied to an interface that does not exist, this interface was deleted:

    
    

     

     

     

    XXXXX@XXXXXE01> show configuration interfaces xe-11/2/6.771

     

    {master}

    XXXXXX@XXXXE01> show configuration interfaces xe-11/2/6.771   

     

    {master}

    jcgutierrez@LTCCNTE01> show policer | match 771

    FP-LIMIT-45M-ge-11/2/6.771-inet-o                       0                    0

    FP-LIMIT-2M-ae0.548-inet-i                      621724284               427717

    FP-LIMIT-20M-ge-11/2/6.771-inet-i                       0                    0

    FP-LIMIT-5M-ge-1/2/7.434-inet-i                  77179301                51571

    FP-LIMIT-11M-ge-0/2/1.826-inet-o               5481392384              3771910

    FP-LIMIT-21M-ae0.549-inet-o                  233437905471            177161014

     

     

     

    I will configure with the configuration that you recommend in the interface new. 

     

     

    Thanks for you help

     

     

     

    Juan Gutierrez

    T.: 3731700 ext. 21460

    QUITO-Ecuador

     

    De: via Juniper Networks [mailto:Mail@community.juniper.net]
    Enviado el: jueves, 20 de mayo de 2021 11:46
    Para: TEC Gutierrez Juan
    Asunto: RE: Junos OS : POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

     

    Hi Juan Carlos, Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a... -posted to the "Junos OS" community

    Junos OS

    Post New Message

     

    Re: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    mriyaz

    May 20, 2021 12:44 PM

    mriyaz

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    www.juniper.net/documentation/en_US/junos/topics/...

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     

     

    Juniper Business Use Only




      Reply to Group Online   View Thread   Recommend   Forward   Flag as Inappropriate  


    When applying the policy it does not work


    XXXXX@XXXXXE01> show configuration interfaces ae1.773
    description "XXXXXXXX";
    vlan-id 773;
    family inet {
    policer {
    input FP-LIMIT-25M;
    output FP-LIMIT-55M;
    }
    address XX.XX.XX.XX/30;

    there is not pilicer in the interface ae1.773


    XXXX@XXXXE01> show policer | match 773
    FP-LIMIT-3M-ge-11/2/6.2712-inet-i 3769773 2559
    FP-LIMIT-1M-ge-1/2/5.795-inet-o 210773671 3394322
    FP-LIMIT-11M-ae1.772-inet-o 5777336586 3872372
    FP-LIMIT-10M-ge-11/2/7.533-inet-o 6093777314 4448029
    FP-LIMIT-10M-ge-11/2/7.2033-inet-i 10457194639 7731254
    FP-LIMIT-3M-ae0.2064-inet-o 117356170773 82924606

    {master}


    Please your help



    ------------------------------
    Juan Gutierrez Cunalata
    ------------------------------



     

     

    You are receiving this message because you followed the 'POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail' message thread. To unsubscribe from this message thread, go to Unsubscribe.

    Update your email preferences to choose the types of email you receive


    <fon size="small" color="gray">"Nota de Descargo: La información contenida en este mensaje y sus anexos tiene carácter confidencial, y está dirigida únicamente al destinatario de la misma y sólo podrá ser usada por éste. Si el lector de este mensaje no es el destinatario del mismo, se le notifica que cualquier copia o distribución de éste se encuentra totalmente prohibida. Si usted ha recibido este mensaje por error, por favor notifique inmediatamente al remitente por este mismo medio y borre el mensaje de su sistema. Las opiniones que contenga este mensaje son exclusivas de su autor y no necesariamente representan la opinión oficial de la CORPORACIÓN NACIONAL DE TELECOMUNICACIONES, CNT EP, DEL ECUADOR." </fon>



    Original Message:
    Sent: 5/20/2021 12:44:00 PM
    From: mriyaz
    Subject: RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-two-color-bandwidth.html

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     


    Juniper Business Use Only