Junos OS

IMPORTANT MODERATION NOTICE

This community is currently under full moderation, meaning  all posts will be reviewed before appearing in the community. Please expect a brief delay—there is no need to post multiple times. If your post is rejected, you'll receive an email outlining the reason(s). We've implemented full moderation to control spam. Thank you for your patience and participation.



Expand all | Collapse all

POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

  • 1.  POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Posted 05-20-2021 11:36


    When applying the policy it does not work


    XXXXX@XXXXXE01> show configuration interfaces ae1.773
    description "XXXXXXXX";
    vlan-id 773;
    family inet {
    policer {
    input FP-LIMIT-25M;
    output FP-LIMIT-55M;
    }
    address XX.XX.XX.XX/30;


    there is not pilicer in the interface ae1.773


    XXXX@XXXXE01> show policer | match 773
    FP-LIMIT-3M-ge-11/2/6.2712-inet-i 3769773 2559
    FP-LIMIT-1M-ge-1/2/5.795-inet-o 210773671 3394322
    FP-LIMIT-11M-ae1.772-inet-o 5777336586 3872372
    FP-LIMIT-10M-ge-11/2/7.533-inet-o 6093777314 4448029
    FP-LIMIT-10M-ge-11/2/7.2033-inet-i 10457194639 7731254
    FP-LIMIT-3M-ae0.2064-inet-o 117356170773 82924606

    {master}


    Please your help




    ------------------------------
    Juan Gutierrez Cunalata
    ------------------------------


  • 2.  RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

     
    Posted 05-20-2021 12:44

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-two-color-bandwidth.html

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     


    Juniper Business Use Only






  • 3.  RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Posted 05-20-2021 13:24

    Hi –R

     

     

    The problem is also seen in that the policy applied to an interface that does not exist, this interface was deleted:

    
    

     

     

     

    XXXXX@XXXXXE01> show configuration interfaces xe-11/2/6.771

     

    {master}

    XXXXXX@XXXXE01> show configuration interfaces xe-11/2/6.771   

     

    {master}

    jcgutierrez@LTCCNTE01> show policer | match 771

    FP-LIMIT-45M-ge-11/2/6.771-inet-o                       0                    0

    FP-LIMIT-2M-ae0.548-inet-i                      621724284               427717

    FP-LIMIT-20M-ge-11/2/6.771-inet-i                       0                    0

    FP-LIMIT-5M-ge-1/2/7.434-inet-i                  77179301                51571

    FP-LIMIT-11M-ge-0/2/1.826-inet-o               5481392384              3771910

    FP-LIMIT-21M-ae0.549-inet-o                  233437905471            177161014

     

     

     

    I will configure with the configuration that you recommend in the interface new. 

     

     

    Thanks for you help

     

     

     

    Juan Gutierrez

    T.: 3731700 ext. 21460

    QUITO-Ecuador

     

    De: via Juniper Networks [mailto:Mail@community.juniper.net]
    Enviado el: jueves, 20 de mayo de 2021 11:46
    Para: TEC Gutierrez Juan
    Asunto: RE: Junos OS : POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

     

    Hi Juan Carlos, Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a... -posted to the "Junos OS" community

    Junos OS

    Post New Message

     

    Re: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    mriyaz

    May 20, 2021 12:44 PM

    mriyaz

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    www.juniper.net/documentation/en_US/junos/topics/...

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     

     

    Juniper Business Use Only




      Reply to Group Online   View Thread   Recommend   Forward   Flag as Inappropriate  


    When applying the policy it does not work


    XXXXX@XXXXXE01> show configuration interfaces ae1.773
    description "XXXXXXXX";
    vlan-id 773;
    family inet {
    policer {
    input FP-LIMIT-25M;
    output FP-LIMIT-55M;
    }
    address XX.XX.XX.XX/30;

    there is not pilicer in the interface ae1.773


    XXXX@XXXXE01> show policer | match 773
    FP-LIMIT-3M-ge-11/2/6.2712-inet-i 3769773 2559
    FP-LIMIT-1M-ge-1/2/5.795-inet-o 210773671 3394322
    FP-LIMIT-11M-ae1.772-inet-o 5777336586 3872372
    FP-LIMIT-10M-ge-11/2/7.533-inet-o 6093777314 4448029
    FP-LIMIT-10M-ge-11/2/7.2033-inet-i 10457194639 7731254
    FP-LIMIT-3M-ae0.2064-inet-o 117356170773 82924606

    {master}


    Please your help



    ------------------------------
    Juan Gutierrez Cunalata
    ------------------------------



     

     

    You are receiving this message because you followed the 'POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail' message thread. To unsubscribe from this message thread, go to Unsubscribe.

    Update your email preferences to choose the types of email you receive


    <fon size="small" color="gray">"Nota de Descargo: La información contenida en este mensaje y sus anexos tiene carácter confidencial, y está dirigida únicamente al destinatario de la misma y sólo podrá ser usada por éste. Si el lector de este mensaje no es el destinatario del mismo, se le notifica que cualquier copia o distribución de éste se encuentra totalmente prohibida. Si usted ha recibido este mensaje por error, por favor notifique inmediatamente al remitente por este mismo medio y borre el mensaje de su sistema. Las opiniones que contenga este mensaje son exclusivas de su autor y no necesariamente representan la opinión oficial de la CORPORACIÓN NACIONAL DE TELECOMUNICACIONES, CNT EP, DEL ECUADOR." </fon>



    Original Message:
    Sent: 5/20/2021 12:44:00 PM
    From: mriyaz
    Subject: RE: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail

    Hi Juan Carlos,

     

    Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.

     

    If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.

     

    https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-two-color-bandwidth.html

     

    Please refer the section "Guidelines for Applying a Bandwidth Policer" for:

     

    "You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."

     

    Hope this helps.

     

    Regards,

    -r.

     

    --------------------------------------------------

     

    If this solves your problem, please mark this post as "Accepted Solution."

    Kudos are always appreciated :).

     

    Sent from Mail for Windows 10

     


    Juniper Business Use Only