Hi –R
The problem is also seen in that the policy applied to an interface that does not exist, this interface was deleted:
XXXXX@XXXXXE01> show configuration interfaces xe-11/2/6.771
{master}
XXXXXX@XXXXE01> show configuration interfaces xe-11/2/6.771
{master}
jcgutierrez@LTCCNTE01> show policer | match 771
FP-LIMIT-45M-ge-11/2/6.771-inet-o 0 0
FP-LIMIT-2M-ae0.548-inet-i 621724284 427717
FP-LIMIT-20M-ge-11/2/6.771-inet-i 0 0
FP-LIMIT-5M-ge-1/2/7.434-inet-i 77179301 51571
FP-LIMIT-11M-ge-0/2/1.826-inet-o 5481392384 3771910
FP-LIMIT-21M-ae0.549-inet-o 233437905471 177161014
I will configure with the configuration that you recommend in the interface new.
Thanks for you help
|
Juan Gutierrez
|
|
|
T.: 3731700 ext. 21460
|
|
|
QUITO-Ecuador
|
De: via Juniper Networks [mailto:Mail@community.juniper.net]
Enviado el: jueves, 20 de mayo de 2021 11:46
Para: TEC Gutierrez Juan
Asunto: RE: Junos OS : POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail
Hi Juan Carlos, Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a... -posted to the "Junos OS" community
Re: POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail
|
|
|
Hi Juan Carlos,
Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.
If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.
www.juniper.net/documentation/en_US/junos/topics/...
Please refer the section "Guidelines for Applying a Bandwidth Policer" for:
"You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."
Hope this helps.
Regards,
-r.
--------------------------------------------------
If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated :).
Sent from Mail for Windows 10
Juniper Business Use Only
|
|
Reply to Group Online View Thread Recommend Forward Flag as Inappropriate
|
Original Message: Sent: 5/20/2021 11:36:00 AM
When applying the policy it does not work
XXXXX@XXXXXE01> show configuration interfaces ae1.773 description "XXXXXXXX"; vlan-id 773; family inet { policer { input FP-LIMIT-25M; output FP-LIMIT-55M; } address XX.XX.XX.XX/30;
there is not pilicer in the interface ae1.773
XXXX@XXXXE01> show policer | match 773 FP-LIMIT-3M-ge-11/2/6.2712-inet-i 3769773 2559 FP-LIMIT-1M-ge-1/2/5.795-inet-o 210773671 3394322 FP-LIMIT-11M-ae1.772-inet-o 5777336586 3872372 FP-LIMIT-10M-ge-11/2/7.533-inet-o 6093777314 4448029 FP-LIMIT-10M-ge-11/2/7.2033-inet-i 10457194639 7731254 FP-LIMIT-3M-ae0.2064-inet-o 117356170773 82924606
{master}
Please your help
------------------------------ Juan Gutierrez Cunalata ------------------------------
|
|
You are receiving this message because you followed the 'POLICER IN MX960 Model: mx960 Junos: 18.1R3.3 Fail' message thread. To unsubscribe from this message thread, go to Unsubscribe.
Update your email preferences to choose the types of email you receive
|
|
<fon size="small" color="gray">"Nota de Descargo: La información contenida en este mensaje y sus anexos tiene carácter confidencial, y está dirigida únicamente al destinatario de la misma y sólo podrá ser usada por éste. Si el lector de este mensaje no es el destinatario del mismo, se le notifica que cualquier copia o distribución de éste se encuentra totalmente prohibida. Si usted ha recibido este mensaje por error, por favor notifique inmediatamente al remitente por este mismo medio y borre el mensaje de su sistema. Las opiniones que contenga este mensaje son exclusivas de su autor y no necesariamente representan la opinión oficial de la CORPORACIÓN NACIONAL DE TELECOMUNICACIONES, CNT EP, DEL ECUADOR." </fon> |
Hi Juan Carlos,
Is this a bandwidth policer by any chane? Because bandwidth policer cannot be applied to an aggregate interface. Such a policer can be applied to the media(ge-, xe-) interfaces.
If you want to use a bandwidth policer on the logical interface, then you might have to configure shaping for individual logical interface as mentioned in the below link.
https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-two-color-bandwidth.html
Please refer the section "Guidelines for Applying a Bandwidth Policer" for:
"You cannot apply a bandwidth policer to an aggregate interface, a tunnel interface, or a software interface."
Hope this helps.
Regards,
-r.
--------------------------------------------------
If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated :).
Sent from Mail for Windows 10
Juniper Business Use Only