Junos OS

 View Only
last person joined: 2 days ago 

Ask questions and share experiences about Junos OS.
  • 1.  MX104 Builtin 10G ports getting signal but not coming up

    Posted 08-16-2021 09:05
    Hi

    We've had around 50 MX104 in our network for about six years and we've had 4 of them on which all buitlin 10G ports have stopped working, starting 2 years ago and on. They have been removed from the network and I have been trying to get them working without success (running install media via USB). When I add the 10G licens the 10G ports show up in the CLI and when I connect them to something else there is incoming signal but the ports just don't come up. Anyone had a similar problem? Is it a hardware failure with no point trying to fix?

    Our Juniper support on these expired long time ago so I can't raise a ticket on the problem unfortunately.

    Please see diagnostics commands below. There is no configuration in the box at all. Version 17.3R3-S2.2

    root> show interfaces diagnostics optics xe-2/0/0 | match "Laser output output power | Laser receiver power "

    Laser output power : 0.4440 mW / -3.53 dBm
    Laser receiver power : 0.4966 mW / -3.04 dBm


    root> show interfaces diagnostics optics xe-2/0/1 | match "Laser output output power | Laser receiver power "
    Laser output power : 0.5330 mW / -2.73 dBm
    Laser receiver power : 0.4150 mW / -3.82 dBm



    root> show interfaces xe-2/0/0
    Physical interface: xe-2/0/0, Enabled, Physical link is Down
    Interface index: 163, SNMP ifIndex: 526
    Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, Speed: 10Gbps,
    BPDU Error: None, Loop Detect PDU Error: None, MAC-REWRITE Error: None,
    Loopback: None, Source filtering: Disabled, Flow control: Enabled
    Pad to minimum frame size: Disabled
    Device flags : Present Running Down
    Interface flags: Hardware-Down SNMP-Traps Internal: 0x0
    Link flags : None
    CoS queues : 8 supported, 8 maximum usable queues
    Current address: f4:cc:55:5d:d5:4a, Hardware address: f4:cc:55:5d:d5:4a
    Last flapped : 2021-08-12 11:33:47 UTC (4d 00:01 ago)
    Input rate : 0 bps (0 pps)
    Output rate : 0 bps (0 pps)
    Active alarms : LINK
    Active defects : LINK, LOCAL-FAULT
    PCS statistics Seconds
    Bit errors 0
    Errored blocks 1
    Link Degrade :
    Link Monitoring : Disable
    Interface transmit statistics: Disabled



    root> show interfaces xe-2/0/1
    Physical interface: xe-2/0/1, Enabled, Physical link is Down
    Interface index: 164, SNMP ifIndex: 527
    Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, Speed: 10Gbps,
    BPDU Error: None, Loop Detect PDU Error: None, MAC-REWRITE Error: None,
    Loopback: None, Source filtering: Disabled, Flow control: Enabled
    Pad to minimum frame size: Disabled
    Device flags : Present Running Down
    Interface flags: Hardware-Down SNMP-Traps Internal: 0x0
    Link flags : None
    CoS queues : 8 supported, 8 maximum usable queues
    Current address: f4:cc:55:5d:d5:4b, Hardware address: f4:cc:55:5d:d5:4b
    Last flapped : 2021-08-12 11:33:47 UTC (4d 00:13 ago)
    Input rate : 0 bps (0 pps)
    Output rate : 0 bps (0 pps)
    Active alarms : LINK
    Active defects : LINK, LOCAL-FAULT
    PCS statistics Seconds
    Bit errors 0
    Errored blocks 0
    Link Degrade :
    Link Monitoring : Disable
    Interface transmit statistics: Disabled
    CoS queues : 8 supported, 8 maximum usable queues
    Current address: f4:cc:55:5d:d5:4b, Hardware address: f4:cc:55:5d:d5:4b
    Last flapped : 2021-08-12 11:33:47 UTC (4d 00:01 ago)
    Input rate : 0 bps (0 pps)
    Output rate : 0 bps (0 pps)
    Active alarms : LINK
    Active defects : LINK, LOCAL-FAULT
    PCS statistics Seconds
    Bit errors 0
    Errored blocks 0
    Link Degrade :
    Link Monitoring : Disable
    Interface transmit statistics: Disabled


    Erac


  • 2.  RE: MX104 Builtin 10G ports getting signal but not coming up

    Posted 08-17-2021 05:37
    Can you confirm the 10 gig port license is installed on the mx104
    show system license

    And naturally that the optics in the mx104 match the mode and frequency of the partner on the link and there are no alarms or warnings in the optic diagnostics.

    ------------------------------
    Steve Puluka BSEET - Juniper Ambassador
    IP Architect - DQE Communications Pittsburgh, PA (Metro Ethernet & ISP)
    http://puluka.com/home
    ------------------------------



  • 3.  RE: MX104 Builtin 10G ports getting signal but not coming up

    Posted 08-18-2021 05:25
    Hi Steve,

    Thanks for the feedback!

    Yes the license looks correct. Right now I have looped between two 10G ports on the same MX014 using the same 10G SFP's we have hundreds of in the network. Also tried I few others just for the sake of it.  

    Is there anything else I can look for?

    root> show system license
    License usage:
    Licenses Licenses Licenses Expiry
    Feature name used installed needed
    scale-subscriber 0 10 0 permanent
    scale-l2tp 0 1000 0 permanent
    scale-mobile-ip 0 1000 0 permanent
    MX104-2x10Gig-port-0-1 0 1 0 permanent
    MX104-2x10Gig-port-2-3 0 1 0 permanent

    Licenses installed:
    License identifier: E408040024
    License version: 4
    Features:
    MX104-2x10Gig-port-0-1 - MX104 2X10Gig Builtin Port(xe-2/0/0 & xe-2/0/1) upgrade
    permanent
    MX104-2x10Gig-port-2-3 - MX104 2X10Gig Builtin Port(xe-2/0/2 & xe-2/0/3) upgrade
    permanent


    root> show interfaces diagnostics optics xe-2/0/0
    Physical interface: xe-2/0/0
    Laser bias current : 32.250 mA
    Laser output power : 0.4440 mW / -3.53 dBm
    Module temperature : 33 degrees C / 91 degrees F
    Module voltage : 3.2800 V
    Laser receiver power : 0.4889 mW / -3.11 dBm
    Laser bias current high alarm : Off
    Laser bias current low alarm : Off
    Laser bias current high warning : Off
    Laser bias current low warning : Off
    Laser output power high alarm : Off
    Laser output power low alarm : Off
    Laser output power high warning : Off
    Laser output power low warning : Off
    Module temperature high alarm : Off
    Module temperature low alarm : Off
    Module temperature high warning : Off
    Module temperature low warning : Off
    Module voltage high alarm : Off
    Module voltage low alarm : Off
    Module voltage high warning : Off
    Module voltage low warning : Off
    Laser rx power high alarm : Off
    Laser rx power low alarm : Off
    Laser rx power high warning : Off
    Laser rx power low warning : Off
    Laser bias current high alarm threshold : 90.000 mA
    Laser bias current low alarm threshold : 2.000 mA
    Laser bias current high warning threshold : 80.000 mA
    Laser bias current low warning threshold : 4.000 mA
    Laser output power high alarm threshold : 1.0000 mW / 0.00 dBm
    Laser output power low alarm threshold : 0.1580 mW / -8.01 dBm
    Laser output power high warning threshold : 0.7940 mW / -1.00 dBm
    Laser output power low warning threshold : 0.2510 mW / -6.00 dBm
    Module temperature high alarm threshold : 75 degrees C / 167 degrees F
    Module temperature low alarm threshold : -5 degrees C / 23 degrees F
    Module temperature high warning threshold : 70 degrees C / 158 degrees F
    Module temperature low warning threshold : 0 degrees C / 32 degrees F
    Module voltage high alarm threshold : 3.500 V
    Module voltage low alarm threshold : 3.080 V
    Module voltage high warning threshold : 3.480 V
    Module voltage low warning threshold : 3.100 V
    Laser rx power high alarm threshold : 1.0000 mW / 0.00 dBm
    Laser rx power low alarm threshold : 0.0288 mW / -15.41 dBm
    Laser rx power high warning threshold : 0.7943 mW / -1.00 dBm
    Laser rx power low warning threshold : 0.0363 mW / -14.40 dBm

    root> show interfaces diagnostics optics xe-2/0/1
    Physical interface: xe-2/0/1
    Laser bias current : 36.750 mA
    Laser output power : 0.5280 mW / -2.77 dBm
    Module temperature : 30 degrees C / 85 degrees F
    Module voltage : 3.2700 V
    Laser receiver power : 0.4108 mW / -3.86 dBm
    Laser bias current high alarm : Off
    Laser bias current low alarm : Off
    Laser bias current high warning : Off
    Laser bias current low warning : Off
    Laser output power high alarm : Off
    Laser output power low alarm : Off
    Laser output power high warning : Off
    Laser output power low warning : Off
    Module temperature high alarm : Off
    Module temperature low alarm : Off
    Module temperature high warning : Off
    Module temperature low warning : Off
    Module voltage high alarm : Off
    Module voltage low alarm : Off
    Module voltage high warning : Off
    Module voltage low warning : Off
    Laser rx power high alarm : Off
    Laser rx power low alarm : Off
    Laser rx power high warning : Off
    Laser rx power low warning : Off
    Laser bias current high alarm threshold : 90.000 mA
    Laser bias current low alarm threshold : 2.000 mA
    Laser bias current high warning threshold : 80.000 mA
    Laser bias current low warning threshold : 4.000 mA
    Laser output power high alarm threshold : 1.0000 mW / 0.00 dBm
    Laser output power low alarm threshold : 0.1580 mW / -8.01 dBm
    Laser output power high warning threshold : 0.7940 mW / -1.00 dBm
    Laser output power low warning threshold : 0.2510 mW / -6.00 dBm
    Module temperature high alarm threshold : 75 degrees C / 167 degrees F
    Module temperature low alarm threshold : -5 degrees C / 23 degrees F
    Module temperature high warning threshold : 70 degrees C / 158 degrees F
    Module temperature low warning threshold : 0 degrees C / 32 degrees F
    Module voltage high alarm threshold : 3.500 V
    Module voltage low alarm threshold : 3.080 V
    Module voltage high warning threshold : 3.480 V
    Module voltage low warning threshold : 3.100 V
    Laser rx power high alarm threshold : 1.0000 mW / 0.00 dBm
    Laser rx power low alarm threshold : 0.0288 mW / -15.41 dBm
    Laser rx power high warning threshold : 0.7943 mW / -1.00 dBm
    Laser rx power low warning threshold : 0.0363 mW / -14.40 dBm



    root> show chassis pic fpc-slot 2 pic-slot 0
    FPC slot 2, PIC slot 0 information:
    Type 4x 10GE(LAN) SFP+ Builtin
    State Online
    Uptime 12 minutes, 15 seconds

    PIC port information:
    Fiber Xcvr vendor Wave- Xcvr
    Port Cable type type Xcvr vendor part number length Firmware
    0 10GBASE LR SM PRO OPTIX 10GB-SFP-LR-JN 1310 nm 0.0
    1 10GBASE LR SM PRO OPTIX 10GB-SFP-LR-JN 1310 nm 0.0



    Erac