hello Steve,
Thanks again for helping us out here .
I tried the "set protocols source-packet-routing" and the "
protocols mpls lsp-external-controller pccd" , "
protocols pcep pce SERVERNAME spring-capability" and its attributes, but still get the same error.
I was browsing through internet and could find the configuration "set chassis network-services enhanced-ip" helps resolve the issue.
But , in my ACX2200, i do not see an option to configure "enhanced ip"
juniper# set chassis network-services ?
Possible completions: >>>>>>>>>>>>>>>>> no "enhanced-ip" option showing up.
ethernet Ethernet network services
ip IP network services
[edit]
juniper# set chassis network-services
My show version shows :
juniper> show version
Model: acx2200
Junos: 19.4R3-S1.3
JUNOS Base OS boot [19.4R3-S1.3]
JUNOS Base OS Software Suite [19.4R3-S1.3]
JUNOS Crypto Software Suite [19.4R3-S1.3]
JUNOS Packet Forwarding Engine Support (ACX) [19.4R3-S1.3]
JUNOS Web Management [19.4R3-S1.3]
JUNOS Online Documentation [19.4R3-S1.3]
JUNOS SDN Software Suite [19.4R3-S1.3]
JUNOS Services Application Level Gateways [19.4R3-S1.3]
JUNOS Services COS [19.4R3-S1.3]
JUNOS Services Jflow Container package [19.4R3-S1.3]
JUNOS Services Stateful Firewall [19.4R3-S1.3]
JUNOS Services NAT [19.4R3-S1.3]
JUNOS Services RPM [19.4R3-S1.3]
JUNOS Services SOFTWIRE [19.4R3-S1.3]
JUNOS Services Captive Portal and Content Delivery Container package [19.4R3-S1.3]
JUNOS Macsec Software Suite [19.4R3-S1.3]
JUNOS Services Crypto [19.4R3-S1.3]
JUNOS Services IPSec [19.4R3-S1.3]
JUNOS Services RTCOM [19.4R3-S1.3]
JUNOS Services SSL [19.4R3-S1.3]
JUNOS Services TCP-LOG [19.4R3-S1.3]
JUNOS DP Crypto Software Software Suite [19.4R3-S1.3]
JUNOS py-base-powerpc [19.4R3-S1.3]
JUNOS py-base2-powerpc [19.4R3-S1.3]
JUNOS py-extensions-powerpc [19.4R3-S1.3]
JUNOS py-extensions2-powerpc [19.4R3-S1.3]
JUNOS jsd [powerpc-19.4R3-S1.3-jet-1]
JUNOS Kernel Software Suite [19.4R3-S1.3]
JUNOS Routing Software Suite [19.4R3-S1.3]
Is there a version problem ?
Thanks
Aseem.
------------------------------
ASEEM RAI
------------------------------
Original Message:
Sent: 06-22-2021 05:45
From: STEVE PULUKA
Subject: Segment Routing support on ACX2200
My lab is running ospf and am able to configure segment routing on the acx2200.
But I wonder if the requirement may be to also have the configurations setup for source packet routing also under
protocols source-packet-routing
protocols mpls lsp-external-controller pccd
protocols pcep pce SERVERNAME spring-capability (and other required parameters)
------------------------------
Steve Puluka BSEET - Juniper Ambassador
IP Architect - DQE Communications Pittsburgh, PA (Metro Ethernet & ISP)
http://puluka.com/home
Original Message:
Sent: 06-22-2021 02:05
From: ASEEM RAI
Subject: Segment Routing support on ACX2200
hello Steve,
Thank you for your reply .
On 19.4R3 , i was trying to enable the SRGB but get the below error.
[edit]
juniper# commit <<<<<<<<<<<<<<<<<<<<<<<<<< issue observed .
[edit protocols isis source-packet-routing]
'srgb'
can't config SRGB
error: configuration check-out failed
[edit]
juniper#
show chassis output
juniper> show chassis hardware
Hardware inventory:
Item Version Part number Serial number Description
Chassis PX0218230112 ACX2200
Midplane REV 05 650-062885 PX0218230112 ACX2200
Routing Engine BUILTIN BUILTIN Routing Engine
FEB 0 BUILTIN BUILTIN Forwarding Engine Processor
FPC 0 BUILTIN BUILTIN FPC BUILTIN
MIC 0 BUILTIN BUILTIN 4x 1GE(LAN) RJ45
PIC 0 BUILTIN BUILTIN 4x 1GE(LAN) RJ45
MIC 1 BUILTIN BUILTIN 4x 1GE(LAN) SFP, RJ45
PIC 1 BUILTIN BUILTIN 4x 1GE(LAN) SFP, RJ45
MIC 2 BUILTIN BUILTIN 2x 1GE(LAN) SFP
PIC 2 BUILTIN BUILTIN 2x 1GE(LAN) SFP
MIC 3 BUILTIN BUILTIN 2x 10GE(LAN) SFP+
PIC 3 BUILTIN BUILTIN 2x 10GE(LAN) SFP+
Xcvr 0 OMPATI NON-JNPR FC2007131520 SFP+-10G-LR
Xcvr 1 OMPATI NON-JNPR FC2007131591 SFP+-10G-LR
juniper>
show configuration
juniper> show configuration | display set
set version 19.4R3-S1.3
set system root-authentication encrypted-password "$6$mVPMxYNJ$/BOnL9VtlRBX3if8zhYS4DB/z34RBkR48XsoeYmoDZeFwGI/4Q/29Xf6ORawWRLyaVPK02cC4ghcEIt.HbViG1"
set system login user juniper uid 2007
set system login user juniper class super-user
set system login user juniper authentication encrypted-password "$6$sWbmzw9p$qHoCDWDzhQ/mgZLb2uz54fZC47mKiENGUbpqe.ePjdIuIVdIs7cBtL9r56dtW22XX0lGHVw9RuzYxdykGjxZE/"
set system services ssh
set system services telnet
set system syslog user * any emergency
set system syslog file messages any error
set system syslog file messages authorization info
set system syslog file interactive-commands interactive-commands any
set chassis network-services ip
set interfaces xe-0/3/0 speed 10g
set interfaces xe-0/3/0 unit 0 description To_CSR1-2_XE8
set interfaces xe-0/3/0 unit 0 family inet address 10.110.10.10/30
set interfaces xe-0/3/0 unit 0 family iso
set interfaces xe-0/3/0 unit 0 family mpls
set interfaces xe-0/3/1 speed 10g
set interfaces xe-0/3/1 unit 0 description To_CSR1-4_XE0
set interfaces xe-0/3/1 unit 0 family inet address 10.110.10.13/30
set interfaces xe-0/3/1 unit 0 family iso
set interfaces xe-0/3/1 unit 0 family mpls
set interfaces fxp0 unit 0 family inet address 10.110.100.13/24
set interfaces lo0 unit 0 family inet address 10.110.1.3/32
set interfaces lo0 unit 0 family iso address 49.0017.0010.0110.0013.00
set policy-options prefix-list term
set policy-options policy-statement prefix-sid term 1 from route-filter 10.110.1.3/32 exact
set policy-options policy-statement prefix-sid term 1 then prefix-segment index 13
set policy-options policy-statement prefix-sid term 1 then prefix-segment node-segment
set policy-options policy-statement prefix-sid term 1 then accept
set protocols isis backup-spf-options remote-backup-calculation
set protocols isis backup-spf-options node-link-degradation
set protocols isis source-packet-routing
set protocols isis level 1 authentication-key "$9$/rRmAuBEhyMWX"
set protocols isis level 1 authentication-type md5
set protocols isis level 1 wide-metrics-only
set protocols isis interface xe-0/3/0.0 point-to-point
set protocols isis interface xe-0/3/0.0 node-link-protection
set protocols isis interface xe-0/3/0.0 family inet bfd-liveness-detection minimum-interval 10
set protocols isis interface xe-0/3/0.0 family inet bfd-liveness-detection minimum-receive-interval 10
set protocols isis interface xe-0/3/0.0 family inet bfd-liveness-detection multiplier 3
set protocols isis interface xe-0/3/0.0 level 2 disable
set protocols isis interface xe-0/3/0.0 ldp-synchronization
set protocols isis interface xe-0/3/1.0 point-to-point
set protocols isis interface xe-0/3/1.0 node-link-protection
set protocols isis interface xe-0/3/1.0 family inet bfd-liveness-detection minimum-interval 3
set protocols isis interface xe-0/3/1.0 family inet bfd-liveness-detection minimum-receive-interval 3
set protocols isis interface xe-0/3/1.0 family inet bfd-liveness-detection multiplier 3
set protocols isis interface xe-0/3/1.0 level 2 disable
set protocols isis interface xe-0/3/1.0 ldp-synchronization
set protocols isis interface all ldp-synchronization
set protocols isis interface lo0.0 passive
set protocols isis export prefix-sid
set protocols isis lsp-lifetime 65535
set protocols isis max-areas 36
set protocols isis spf-options delay 200
set protocols isis spf-options holddown 2000
set protocols isis spf-options rapid-runs 5
set protocols ldp interface xe-0/3/0.0
set protocols ldp interface xe-0/3/1.0
set protocols mpls interface all
set protocols lldp interface all
------------------------------
ASEEM RAI
Original Message:
Sent: 06-21-2021 20:21
From: STEVE PULUKA
Subject: Segment Routing support on ACX2200
The feature is available on the acx2200 from 17.4. You can configure basic pcep client support and both standard and spring controller. But the label depth on the broadcom chips here is only 3 or 4.
------------------------------
Steve Puluka BSEET - Juniper Ambassador
IP Architect - DQE Communications Pittsburgh, PA (Metro Ethernet & ISP)
http://puluka.com/home
Original Message:
Sent: 06-21-2021 12:47
From: ASEEM RAI
Subject: Segment Routing support on ACX2200
hi Experts.
I am running 19.4R3 version on ACX220 . Any idea if Segment Routing support is available on that platform in the release 19.4R3 . If not, from which version is it going to be or already available.
Thanks
Aseem.
------------------------------
ASEEM RAI
------------------------------