Switching

IMPORTANT MODERATION NOTICE

This community is currently under full moderation, meaning  all posts will be reviewed before appearing in the community. Please expect a brief delay—there is no need to post multiple times. If your post is rejected, you'll receive an email outlining the reason(s). We've implemented full moderation to control spam. Thank you for your patience and participation.



Expand all | Collapse all

QFX5120-48Y 25G transceivers auto-negotiation

  • 1.  QFX5120-48Y 25G transceivers auto-negotiation

     
    Posted 07-29-2021 09:22
    Hi all

    Been searching through documentations but can't find the right answer

    https://www.juniper.net/documentation/us/en/software/junos/interfaces-ethernet-switches/topics/topic-map/switches-interface-gigabit.html#d565e910


    Does anyone has idea  if

    • Is speed / duplex setting supported on 25G transceiver in QFX5120-48Y ?
    • Without any auto-negotiation configuration - is auto-negotiate enabled / disabled on 25G interface ?
    • How do we verify that ? show interface et-0/0/x extensive does not show any auto-negotiate settings

    Thank you


  • 2.  RE: QFX5120-48Y 25G transceivers auto-negotiation

    Posted 07-29-2021 10:24
    to see what auto-neg the switch knows about  try   .. I have no QFX with 10/25/50/100 so ymmv.
    show interfaces et-0/0/x media

    Autonegotiation information:
    Negotiation status: Complete
    Link partner:
    Link mode: Full-duplex, Flow control: Symmetric/Asymmetric, Remote fault: OK, Link partner Speed: 1000 Mbps
    Local resolution:
    Flow control: None, Flow control tx: None, Flow control rx: None, Remote fault: Link OK


  • 3.  RE: QFX5120-48Y 25G transceivers auto-negotiation

     
    Posted 08-02-2021 05:28

    Can't find anything related to negotiation in the output though

    show interfaces et-0/0/31 media
    Physical interface: et-0/0/31, Enabled, Physical link is Up
      Interface index: 679, SNMP ifIndex: 555
      Link-level type: Ethernet, MTU: 9216, LAN-PHY mode, Speed: 25Gbps,
      BPDU Error: None, Loop Detect PDU Error: None, Ethernet-Switching Error: None,
      MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled,
      Flow control: Disabled, Media type: Fiber
      Device flags   : Present Running
      Interface flags: SNMP-Traps Internal: 0x4000
      Link flags     : None
      CoS queues     : 10 supported, 10 maximum usable queues
      Current address: 84:03:28:2e:8d:23, Hardware address: 84:03:28:2e:8d:23
      Last flapped   : 2021-07-31 16:20:30 SGT (22:55:02 ago)
      Input rate     : 4783072 bps (708 pps)
      Output rate    : 14447064 bps (827 pps)
      Active alarms  : None
      Active defects : None
      PCS statistics                      Seconds
        Bit errors                             0
        Errored blocks                         0
      Ethernet FEC Mode  :                  FEC74
      Ethernet FEC statistics              Errors
        FEC Corrected Errors                    0
        FEC Uncorrected Errors                  0
        FEC Corrected Errors Rate               0
        FEC Uncorrected Errors Rate             0
      MAC statistics:
        Input bytes: 36310827560, Input packets: 17887797,
        Output bytes: 54802385162, Output packets: 19675913
      PRBS Statistics : Disabled
      Interface transmit statistics: Disabled​



  • 4.  RE: QFX5120-48Y 25G transceivers auto-negotiation

    Posted 07-30-2021 05:37
    Q: "Is speed / duplex setting supported on 25G transceiver in QFX5120-48?"
    A: I think 10 G and 25 G standards only have full duplex and no auto negotiation so you cannot select half and auto for that reason.

    25 G optics do require special FEC settings from time to time. set interfaces et-0/0/X ether-options fec ???


  • 5.  RE: QFX5120-48Y 25G transceivers auto-negotiation

     
    Posted 08-02-2021 05:28
    @fb35523

    any idea what will happen if i were to set auto-negotiation on such interface ?
    set interface et-0/0/30 ether-options auto-negotation​​

    on the fec settings - does that means i will have to check with the host end on what fec setting do they prefer ?

    set interfaces et-0/0/30 optics-options fec ?
    Possible completions:
      hgfec                High Gain Forward Error Correction
      sdfec                Sky-Compatible Soft Decision Forward Error Correction
      sdfec15              Soft Decision Forward Error Correction with 15 percent overhead
      sdfec25              Denali-Compatible Soft Decision Forward Error Correction with 25 percent overhead​

    which option is FEC74  -- show interfaces extensive reflects that i am using FEC74 on the 25G interface




  • 6.  RE: QFX5120-48Y 25G transceivers auto-negotiation

    Posted 08-02-2021 05:47
    If the FEC is not setup the same on both ends, the link will not work at all. I had a bit of a struggle to find the cause when I had this problem the first time, so me mentioning FEC was more of a heads up for you that you might have to look for that as well if you bump into problems.

    As for auto-negotiation, I don't think it will commit or it will not matter as the setting is irrelevant for 25 G. Try it out!