May i know whether someone here can share how to configure ACX5448 as function layer 2 switch. I means trunk and access port configuration. As i'm check the acx5448 dont have know interface-mode trunk. So what knob that i need to use?
Thanks and appreciate your feedback.
Greetings, ACX Series routers do not support the creation of bridge domains by using access and trunk ports.
On ACX Series routers, you can configure bridge domains by using the following methods:
• Bridge domain without a vlan-id number statement• Bridge domain with the vlan-id value set to none• Bridge domain with a single vlan-id• Bridge domain with a vlan-id-list
Layer 2 Bridge Domains on ACX Series Overviewhttps://www.juniper.net/documentation/en_US/junos/topics/concept/layer-2-services-bridging-overview-acx-series.html
Configuring a Bridge Domain on ACX Series Routershttps://www.juniper.net/documentation/en_US/junos/topics/task/configuration/layer-2-services-configuring-bridge-domain-acx-series.html
If this solves your problem, please mark this post as "Accepted Solution" so we can help others too \:)/
Lil DexxJNCIE-ENT#863, 3X JNCIP-[SP-ENT-DC], 4X JNCIA [cloud-DevOps-Junos-Design], Champions Ingenius, SSYB
Based on the url tat u give it's look like i'm need to look on url below right? Do u have exactly example configuration trunk port and access port on ACX5548 that has been tested working?
Thanks and appreciate any help.
This should do the job if the if your device is connected to another one that is trunking VLAN 10 and 20
set interfaces xe-0/0/5 flexible-vlan-taggingset interfaces xe-0/0/5 encapsulation flexible-ethernet-servicesset interfaces xe-0/0/5 unit 10 encapsulation vlan-bridgeset interfaces xe-0/0/5 unit 10 vlan-id 10set interfaces xe-0/0/5 unit 10 family ethernet-switchingset interfaces xe-0/0/5 unit 20 encapsulation vlan-bridgeset interfaces xe-0/0/5 unit 20 vlan-id 20set interfaces xe-0/0/5 unit 20 family ethernet-switchingset interfaces irb unit 10 family inet address 10.10.10.2/24set interfaces irb unit 20 family inet address 184.108.40.206/24
set vlans vlan10 vlan-id 10set vlans vlan10 interface xe-0/0/5.10set vlans vlan10 l3-interface irb.10set vlans vlan20 vlan-id 20set vlans vlan20 interface xe-0/0/5.20set vlans vlan20 l3-interface irb.20
For the access interface can you try it without the VLAN ID? unfortunately, I don't have the resources to test this out.
There is also the option to use a native VLAN if you need untagged traffic on that same interface.
set interfaces xe-0/0/5 native-vlan-id 15
Please let me know how it goes, eager to hear about it!
Below config not work. Error appear during commit.
set interfaces xe-0/0/5 flexible-vlan-taggingset interfaces xe-0/0/5 encapsulation flexible-ethernet-servicesset interfaces xe-0/0/5 unit 10 encapsulation vlan-bridgeset interfaces xe-0/0/5 unit 10 vlan-id 10set interfaces xe-0/0/5 unit 10 family ethernet-switchingset interfaces xe-0/0/5 unit 20 encapsulation vlan-bridgeset interfaces xe-0/0/5 unit 20 vlan-id 20set interfaces xe-0/0/5 unit 20 family ethernet-switching
Can you paste the error that you are getting while committing the config ?
Have you created the vlan and attached to interface ?
To make the access port on ACX i try to not assign vlan-id on that interface but it throw the error. So do u have idea config access port on ACX.
Thanks and appreciate your feedback