Consoles: U-Boot console
Found compatible API, ver. 7

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1
(marcelm@apg-bbuild01.juniper.net, Wed Feb  6 11:23:55 PST 2008)
Memory: 512MB
Loading /boot/defaults/loader.conf
/kernel data=0x9ef8d0+0x6ed84 syms=[0x4+0x88ad0+0x4+0x8f1e6]


Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0xa0000100 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1996-2008, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 9.2R2.15 #0: 2008-10-03 19:20:25 UTC
    builder@amalath.juniper.net:/volume/build/junos/9.2/release/9.2R2.15/obj-pow
erpc/sys/compile/JUNIPER-EX
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
Timecounter "decrementer" frequency 37500000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory  = 512753664 (489 MB)
avail memory = 501309440 (478 MB)
ETHERNET SOCKET BRIDGE initialising
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocp
bus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff0000
00-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on o
cpbus0
tsec0: hardware MAC address 00:23:9c:00:7a:3f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto

pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf00
00000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at
device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0af
ff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff on ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0x
a0000000-0xa3ffffff irq 18 at device 0.0 on pci2
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpb
us0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpb
us0
idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0
bme0:Virtual BME driver initializing
Timecounters tick every 1.000 msec
Loading common multilink module.
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s2a
WARNING: / was not properly dismounted
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Jan 13 14:58:03 init: login_getclass: unknown class 'daemon'
cd: can't cd to /etc/db/pkg
savecore: could not be determined
savecore: could not be determined
No dump exists
Automatic reboot in progressJWARNING: system watchdog timer still running,
         use '/sbin/watchdog -off' to disable
Enter full pathname of shell or 'recovery' for root password recovery or RETURN
for /bin/sh: ?
NOTE: to go to multi-user operation, exit the single-user shell (with ^D)
Jan 13 14:58:44 init: can't exec /packages/mnt/jbase? for single user: No such f
ile or directory
# recovery
recovery: not found
#

U-Boot 1.1.6 (Feb  6 2008 - 11:27:42)

Board: EX3200-24T 2.13
EPLD:  Version 6.0 (0x85)
DRAM:  Initializing (512 MB)
FLASH: 8 MB
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

Consoles: U-Boot console
Found compatible API, ver. 7

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1
(marcelm@apg-bbuild01.juniper.net, Wed Feb  6 11:23:55 PST 2008)
Memory: 512MB
Loading /boot/defaults/loader.conf
/kernel data=0x9ef8d0+0x6ed84 syms=[0x4+0x88ad0+0x4+0x8f1e6]


Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0xa0000100 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1996-2008, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 9.2R2.15 #0: 2008-10-03 19:20:25 UTC
    builder@amalath.juniper.net:/volume/build/junos/9.2/release/9.2R2.15/obj-pow
erpc/sys/compile/JUNIPER-EX
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
Timecounter "decrementer" frequency 37500000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory  = 512753664 (489 MB)
avail memory = 501309440 (478 MB)
ETHERNET SOCKET BRIDGE initialising
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocp
bus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff0000
00-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on o
cpbus0
tsec0: hardware MAC address 00:23:9c:00:7a:3f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto

pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf00
00000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at
device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0af
ff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff on ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0x
a0000000-0xa3ffffff irq 18 at device 0.0 on pci2
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpb
us0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpb
us0
idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0
bme0:Virtual BME driver initializing
Timecounters tick every 1.000 msec
Loading common multilink module.
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s2a
WARNING: / was not properly dismounted
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Jan 13 14:58:03 init: login_getclass: unknown class 'daemon'
cd: can't cd to /etc/db/pkg
savecore: could not be determined
savecore: could not be determined
No dump exists
Automatic reboot in progressJWARNING: system watchdog timer still running,
         use '/sbin/watchdog -off' to disable
Enter full pathname of shell or 'recovery' for root password recovery or RETURN
for /bin/sh: reboot
NOTE: to go to multi-user operation, exit the single-user shell (with ^D)
Jan 13 15:04:26 init: can't exec /packages/mnt/jbasereboot for single user: No s
uch file or directory
# cls
cls: not found
# clear
tput: no terminal type specified and no TERM environmental variable.
#
# root
root: Permission denied
# restart
restart: not found
# reboot
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 0 0 0 0 0 0 0 0 done

syncing disks... All buffers synced.
Uptime: 7m4s
Rebooting...


U-Boot 1.1.6 (Feb  6 2008 - 11:27:42)

Board: EX3200-24T 2.13
EPLD:  Version 6.0 (0x85)
DRAM:  Initializing (512 MB)
FLASH: 8 MB
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

Consoles: U-Boot console
Found compatible API, ver. 7

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1
(marcelm@apg-bbuild01.juniper.net, Wed Feb  6 11:23:55 PST 2008)
Memory: 512MB
Loading /boot/defaults/loader.conf
/kernel data=0x9ef8d0+0x6ed84 syms=[0x4+0x88ad0+0x4+0x8f1e6]


Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0xa0000100 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1996-2008, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 9.2R2.15 #0: 2008-10-03 19:20:25 UTC
    builder@amalath.juniper.net:/volume/build/junos/9.2/release/9.2R2.15/obj-pow
erpc/sys/compile/JUNIPER-EX
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
Timecounter "decrementer" frequency 37500000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory  = 512753664 (489 MB)
avail memory = 501309440 (478 MB)
ETHERNET SOCKET BRIDGE initialising
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocp
bus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff0000
00-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on o
cpbus0
tsec0: hardware MAC address 00:23:9c:00:7a:3f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto

pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf00
00000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at
device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0af
ff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff on ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0x
a0000000-0xa3ffffff irq 18 at device 0.0 on pci2
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpb
us0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpb
us0
idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0
bme0:Virtual BME driver initializing
Timecounters tick every 1.000 msec
Loading common multilink module.
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s2a
WARNING: / was not properly dismounted
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Jan 13 14:58:03 init: login_getclass: unknown class 'daemon'
cd: can't cd to /etc/db/pkg
savecore: could not be determined
savecore: could not be determined
No dump exists
Automatic reboot in progressJWARNING: system watchdog timer still running,
         use '/sbin/watchdog -off' to disable
Enter full pathname of shell or 'recovery' for root password recovery or RETURN
for /bin/sh: recovery
machdep.bootsuccess: 0 -> 0

Performing initialization of management services ...
mgd: not found

error: initialization of management services (mgd -S) failed

An emergency shell can be started to repair any damage and
perform the required operation before exiting and allowing
this script to continue operation.

continue, shell, abort, retry, or reboot ? continue

rpdc: not found



rpdc: not found
reboot


U-Boot 1.1.6 (Feb  6 2008 - 11:27:42)

Board: EX3200-24T 2.13
EPLD:  Version 6.0 (0x85)
DRAM:  Initializing (512 MB)
FLASH: 8 MB
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

Consoles: U-Boot console
Found compatible API, ver. 7

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1
(marcelm@apg-bbuild01.juniper.net, Wed Feb  6 11:23:55 PST 2008)
Memory: 512MB
Loading /boot/defaults/loader.conf
/kernel data=0x9ef8d0+0x6ed84 syms=[0x4+0x88ad0+0x4+0x8f1e6]


Hit [Enter] to boot immediately, or space bar for command prompt.
Booting [/kernel]...
Kernel entry at 0xa0000100 ...
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1996-2008, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 9.2R2.15 #0: 2008-10-03 19:20:25 UTC
    builder@amalath.juniper.net:/volume/build/junos/9.2/release/9.2R2.15/obj-pow
erpc/sys/compile/JUNIPER-EX
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
Timecounter "decrementer" frequency 37500000 Hz quality 0
cpu0: Freescale e500v2 core revision 2.2
cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE>
real memory  = 512753664 (489 MB)
avail memory = 501309440 (478 MB)
ETHERNET SOCKET BRIDGE initialising
nexus0: <PPC e500 Nexus device>
ocpbus0: <on-chip peripheral bus> on nexus0
openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocp
bus0
uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0
uart0: console (9600,n,8,1)
uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0
lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff0000
00-0xffffffff irq 22 on ocpbus0
cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0
syspld0 iomem 0xff000000-0xff00ffff on lbc0
tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on o
cpbus0
tsec0: hardware MAC address 00:23:9c:00:7a:3f
miibus0: <MII bus> on tsec0
e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto

pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf00
00000-0xf3ffffff on ocpbus0
pci0: <PCI bus> on pcib0
pci0: <serial bus, USB> at device 18.0 (no driver attached)
ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at
device 18.2 on pci0
usb0: EHCI version 1.0
usb0: <Philips ISP156x USB 2.0 controller> on ehci0
usb0: USB revision 2.0
uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 2
pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0af
ff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff on ocpbus0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci1
pci2: <PCI bus> on pcib2
mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0x
a0000000-0xa3ffffff irq 18 at device 0.0 on pci2
i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpb
us0
i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpb
us0
idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0
bme0:Virtual BME driver initializing
Timecounters tick every 1.000 msec
Loading common multilink module.
IPsec: Initialized Security Association Processing.
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from ufs:/dev/da0s2a
WARNING: / was not properly dismounted
Attaching /packages/jbase via /dev/mdctl...
Mounted jbase package on /dev/md0...
Jan 13 14:58:03 init: login_getclass: unknown class 'daemon'
cd: can't cd to /etc/db/pkg
savecore: could not be determined
savecore: could not be determined
No dump exists
Automatic reboot in progressJWARNING: system watchdog timer still running,
         use '/sbin/watchdog -off' to disable
Enter full pathname of shell or 'recovery' for root password recovery or RETURN
for /bin/sh: