term len 0 Labo_cisco_switch#sh vers Cisco IOS Software, C3750 Software (C3750-IPBASE-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 28-Jul-06 08:46 by yenanh Image text-base: 0x00003000, data-base: 0x00EE3E54 ROM: Bootstrap program is C3750 boot loader BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4) Labo_cisco_switch uptime is 2 hours, 17 minutes System returned to ROM by power-on System image file is "flash:c3750-ipbase-mz.122-25.SEE2/c3750-ipbase-mz.122-25.SEE2.bin" cisco WS-C3750-24TS (PowerPC405) processor (revision L0) with 118784K/12280K bytes of memory. Processor board ID CAT1104NJY4 Last reset from power-on 2 Virtual Ethernet interfaces 24 FastEthernet interfaces 2 Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00:1A:E3:54:86:80 Motherboard assembly number : 73-9677-10 Power supply part number : 341-0034-01 Motherboard serial number : CAT11045HMQ Power supply serial number : DTH110111C2 Model revision number : L0 Motherboard revision number : A0 Model number : WS-C3750-24TS-S System serial number : CAT1104NJY4 Top Assembly Part Number : 800-25857-02 Top Assembly Revision Number : D0 Version ID : V05 CLEI Code Number : CNMV100CRE Hardware Board Revision Number : 0x01 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 26 WS-C3750-24TS 12.2(25)SEE2 C3750-IPBASE-M Configuration register is 0xF Labo_cisco_switch#sh run Building configuration... Current configuration : 2898 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Labo_cisco_switch ! enable secret 5 $1$tWox$9iQPuS8GPtEts.PZGvlLs. enable password cisco ! no aaa new-model switch 1 provision ws-c3750-24ts vtp domain test vtp mode transparent ip subnet-zero ! ! ! ! no file verify auto spanning-tree mode pvst no spanning-tree optimize bpdu transmission spanning-tree extend system-id ! vlan internal allocation policy ascending ! vlan 2 name Users ! vlan 3 name Servers ! vlan 25 name test ! vlan 100 name Transit ! vlan 101 name vlan101 ! vlan 410 name WAN ! vlan 804,810,855 ! interface Port-channel1 description === LACP Trunk to Juniper === switchport trunk encapsulation dot1q switchport mode trunk ! interface Port-channel2 description === LACP Trunk to Cisco 2950 === switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet1/0/1 switchport access vlan 2 switchport mode access spanning-tree portfast ! interface FastEthernet1/0/2 switchport access vlan 3 switchport mode access ! interface FastEthernet1/0/3 ! interface FastEthernet1/0/4 ! interface FastEthernet1/0/5 ! interface FastEthernet1/0/6 ! interface FastEthernet1/0/7 ! interface FastEthernet1/0/8 ! interface FastEthernet1/0/9 ! interface FastEthernet1/0/10 ! interface FastEthernet1/0/11 ! interface FastEthernet1/0/12 ! interface FastEthernet1/0/13 ! interface FastEthernet1/0/14 ! interface FastEthernet1/0/15 ! interface FastEthernet1/0/16 ! interface FastEthernet1/0/17 ! interface FastEthernet1/0/18 ! interface FastEthernet1/0/19 ! interface FastEthernet1/0/20 description === LACP Trunk uplink1 to Cisco 2950 === switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 2 mode active ! interface FastEthernet1/0/21 description === LACP Trunk uplink2 to Cisco 2950 === switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 2 mode active ! interface FastEthernet1/0/22 description === LACP Trunk uplink to Juniper === switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 1 mode active ! interface FastEthernet1/0/23 description === LACP Trunk uplink to Juniper === switchport trunk encapsulation dot1q switchport mode trunk channel-protocol lacp channel-group 1 mode active ! interface FastEthernet1/0/24 description === Single Trunk uplink to Juniper === switchport trunk encapsulation dot1q switchport mode trunk ! interface GigabitEthernet1/0/1 ! interface GigabitEthernet1/0/2 ! interface Vlan1 no ip address ! interface Vlan2 ip address 192.168.2.20 255.255.255.0 no ip route-cache ! ip default-gateway 192.168.2.1 ip classless ip http server ! ! control-plane ! ! line con 0 line vty 0 4 password cisco login line vty 5 15 password cisco login ! end Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh eth Labo_cisco_switch#sh etherchannel 1 % Incomplete command. Labo_cisco_switch#sh etherchannel 1 ? detail Detail information port Port information port-channel Port-channel information protocol protocol enabled summary One-line summary per channel-group Labo_cisco_switch#sh etherchannel 1 de Group state = L2 Ports: 2 Maxports = 16 Port-channels: 1 Max Port-channels = 16 Protocol: LACP Ports in the group: ------------------- Port: Fa1/0/22 ------------ Port state = Up Mstr Assoc In-Bndl Channel group = 1 Mode = Active Gcchange = - Port-channel = Po1 GC = - Pseudo port-channel = Po1 Port index = 0 Load = 0x00 Protocol = LACP Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs. A - Device is in active mode. P - Device is in passive mode. Local information: LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/22 SA bndl 32768 0x1 0x1 0x18 0x3D Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/22 FA 127 0019.e251.b080 15s 0x1 0x20F 0x3F Age of the port in the current state: 00d:00h:11m:41s Port: Fa1/0/23 ------------ Port state = Up Mstr Assoc In-Bndl Channel group = 1 Mode = Active Gcchange = - Port-channel = Po1 GC = - Pseudo port-channel = Po1 Port index = 0 Load = 0x00 Protocol = LACP Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs. A - Device is in active mode. P - Device is in passive mode. Local information: LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/23 SA bndl 32768 0x1 0x1 0x19 0x3D Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/23 FA 127 0019.e251.b080 16s 0x1 0x20E 0x3F Age of the port in the current state: 00d:00h:11m:44s Port-channels in the group: --------------------------- Port-channel: Po1 (Primary Aggregator) ------------ Age of the Port-channel = 00d:02h:17m:00s Logical slot/port = 10/1 Number of ports = 2 HotStandBy port = null Port state = Port-channel Ag-Inuse Protocol = LACP Ports in the Port-channel: Index Load Port EC state No of bits ------+------+------+------------------+----------- 0 00 Fa1/0/22 Active 0 0 00 Fa1/0/23 Active 0 Time since last port bundled: 00d:00h:11m:43s Fa1/0/22 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh etherchannel 1 ? detail Detail information port Port information port-channel Port-channel information protocol protocol enabled summary One-line summary per channel-group Labo_cisco_switch#sh etherchannel 1 port Ports in the group: ------------------- Port: Fa1/0/22 ------------ Port state = Up Mstr Assoc In-Bndl Channel group = 1 Mode = Active Gcchange = - Port-channel = Po1 GC = - Pseudo port-channel = Po1 Port index = 0 Load = 0x00 Protocol = LACP Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs. A - Device is in active mode. P - Device is in passive mode. Local information: LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/22 SA bndl 32768 0x1 0x1 0x18 0x3D Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/22 FA 127 0019.e251.b080 24s 0x1 0x20F 0x3F Age of the port in the current state: 00d:00h:11m:50s Port: Fa1/0/23 ------------ Port state = Up Mstr Assoc In-Bndl Channel group = 1 Mode = Active Gcchange = - Port-channel = Po1 GC = - Pseudo port-channel = Po1 Port index = 0 Load = 0x00 Protocol = LACP Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs. A - Device is in active mode. P - Device is in passive mode. Local information: LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/23 SA bndl 32768 0x1 0x1 0x19 0x3D Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/23 FA 127 0019.e251.b080 25s 0x1 0x20E 0x3F Age of the port in the current state: 00d:00h:11m:53s Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh etherchannel 1 ? detail Detail information port Port information port-channel Port-channel information protocol protocol enabled summary One-line summary per channel-group Labo_cisco_switch#sh etherchannel 1 po Labo_cisco_switch#sh etherchannel 1 port- Labo_cisco_switch#sh etherchannel 1 port-channel 1 ^ % Invalid input detected at '^' marker. Labo_cisco_switch#sh etherchannel 1 port-channel ? | Output modifiers Labo_cisco_switch#sh etherchannel 1 port-channel Port-channels in the group: --------------------------- Port-channel: Po1 (Primary Aggregator) ------------ Age of the Port-channel = 00d:02h:17m:20s Logical slot/port = 10/1 Number of ports = 2 HotStandBy port = null Port state = Port-channel Ag-Inuse Protocol = LACP Ports in the Port-channel: Index Load Port EC state No of bits ------+------+------+------------------+----------- 0 00 Fa1/0/22 Active 0 0 00 Fa1/0/23 Active 0 Time since last port bundled: 00d:00h:12m:04s Fa1/0/22 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh etherchannel 1 proto Labo_cisco_switch#sh etherchannel 1 protocol ? | Output modifiers Labo_cisco_switch#sh etherchannel 1 protocol Protocol: LACP Labo_cisco_switch#sh etherchannel 1 ? detail Detail information port Port information port-channel Port-channel information protocol protocol enabled summary One-line summary per channel-group Labo_cisco_switch#sh etherchannel 1 sum Flags: D - down P - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3 S - Layer2 U - in use f - failed to allocate aggregator u - unsuitable for bundling w - waiting to be aggregated d - default port Number of channel-groups in use: 2 Number of aggregators: 2 Group Port-channel Protocol Ports ------+-------------+-----------+----------------------------------------------- 1 Po1(SU) LACP Fa1/0/22(P) Fa1/0/23(P) Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh l Labo_cisco_switch#sh la Labo_cisco_switch#sh lacp % Incomplete command. Labo_cisco_switch#sh lacp nei Flags: S - Device is requesting Slow LACPDUs F - Device is requesting Fast LACPDUs A - Device is in Active mode P - Device is in Passive mode Channel group 1 neighbors Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/22 FA 127 0019.e251.b080 6s 0x1 0x20F 0x3F Fa1/0/23 FA 127 0019.e251.b080 6s 0x1 0x20E 0x3F Channel group 2 neighbors Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/20 SP 32768 000b.5f76.5380 3722s 0x1 0x15 0x34 Fa1/0/21 SP 32768 000b.5f76.5380 3704s 0x1 0x16 0x34 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh lacp ? <1-48> Channel group number counters Traffic information internal Internal information neighbor Neighbor information sys-id LACP System ID Labo_cisco_switch#sh lacp 1 cou LACPDUs Marker Marker Response LACPDUs Port Sent Recv Sent Recv Sent Recv Pkts Err --------------------------------------------------------------------- Channel group: 1 Fa1/0/22 1068 30 0 0 0 0 0 Fa1/0/23 1074 30 0 0 0 0 0 Labo_cisco_switch# Labo_cisco_switch#sh lacp 1 cou LACPDUs Marker Marker Response LACPDUs Port Sent Recv Sent Recv Sent Recv Pkts Err --------------------------------------------------------------------- Channel group: 1 Fa1/0/22 1070 30 0 0 0 0 0 Fa1/0/23 1076 30 0 0 0 0 0 Labo_cisco_switch#sh lacp ? <1-48> Channel group number counters Traffic information internal Internal information neighbor Neighbor information sys-id LACP System ID Labo_cisco_switch#sh lacp inte Flags: S - Device is requesting Slow LACPDUs F - Device is requesting Fast LACPDUs A - Device is in Active mode P - Device is in Passive mode Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/22 SA bndl 32768 0x1 0x1 0x18 0x3D Fa1/0/23 SA bndl 32768 0x1 0x1 0x19 0x3D Channel group 2 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State Fa1/0/20 SA down 32768 0x2 0x2 0x16 0x5 Fa1/0/21 SA down 32768 0x2 0x2 0x17 0x5 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh lacp nei Flags: S - Device is requesting Slow LACPDUs F - Device is requesting Fast LACPDUs A - Device is in Active mode P - Device is in Passive mode Channel group 1 neighbors Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/22 FA 127 0019.e251.b080 1s 0x1 0x20F 0x3F Fa1/0/23 FA 127 0019.e251.b080 1s 0x1 0x20E 0x3F Channel group 2 neighbors Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa1/0/20 SP 32768 000b.5f76.5380 3747s 0x1 0x15 0x34 Fa1/0/21 SP 32768 000b.5f76.5380 3729s 0x1 0x16 0x34 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch#sh lacp sys Labo_cisco_switch#sh lacp sys-id 32768, 001a.e354.8680 Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# Labo_cisco_switch# ========================================================================================== ========================================================================================== show | display set set version 9.1R2.10 set system host-name LAB_EX-0 set system time-zone Europe/Brussels set system authentication-order password set system root-authentication encrypted-password "$1$JZIpfEzy$L/LbSm2gWvlMReKTxVVyH/" set system login user wide full-name WilliamDevos set system login user wide uid 100 set system login user wide class super-user set system login user wide authentication encrypted-password 1QzfxXdSnt5RQ set system services ssh set system services telnet connection-limit 10 set system services web-management http set system services web-management session idle-timeout 15 set system services web-management session session-limit 5 set system syslog user * any emergency set system syslog file messages any notice set system syslog file messages authorization info set system syslog file interactive-commands interactive-commands any set chassis aggregated-devices ethernet device-count 2 set interfaces ge-0/0/0 unit 0 description UserPort0 set interfaces ge-0/0/0 unit 0 family ethernet-switching vlan members Users set interfaces ge-0/0/1 unit 0 family ethernet-switching set interfaces ge-0/0/2 unit 0 family ethernet-switching set interfaces ge-0/0/3 unit 0 family ethernet-switching set interfaces ge-0/0/4 unit 0 family ethernet-switching set interfaces ge-0/0/5 unit 0 family ethernet-switching set interfaces ge-0/0/6 unit 0 family ethernet-switching set interfaces ge-0/0/7 unit 0 family ethernet-switching set interfaces ge-0/0/8 unit 0 family ethernet-switching set interfaces ge-0/0/9 unit 0 family ethernet-switching set interfaces ge-0/0/10 unit 0 family ethernet-switching set interfaces ge-0/0/11 unit 0 family ethernet-switching set interfaces ge-0/0/12 unit 0 family ethernet-switching set interfaces ge-0/0/13 unit 0 description ServerPort0 set interfaces ge-0/0/13 unit 0 family ethernet-switching vlan members Servers set interfaces ge-0/0/14 ether-options 802.3ad ae0 ---(more)--- set interfaces ge-0/0/15 ether-options 802.3ad ae0 set interfaces ge-0/0/16 unit 0 family ethernet-switching set interfaces ge-0/0/17 unit 0 family ethernet-switching set interfaces ge-0/0/18 unit 0 family ethernet-switching set interfaces ge-0/0/19 unit 0 family ethernet-switching set interfaces ge-0/0/20 unit 0 family ethernet-switching set interfaces ge-0/0/21 unit 0 family ethernet-switching set interfaces ge-0/0/22 apply-macro juniper-port-profile "Layer 2 Uplink" set interfaces ge-0/0/22 description "Cisco Switch" set interfaces ge-0/0/22 mtu 1514 set interfaces ge-0/0/22 ether-options auto-negotiation set interfaces ge-0/0/22 ether-options no-flow-control set interfaces ge-0/0/22 ether-options link-mode automatic set interfaces ge-0/0/22 ether-options speed auto-negotiation set interfaces ge-0/0/22 unit 0 family ethernet-switching port-mode trunk set interfaces ge-0/0/22 unit 0 family ethernet-switching vlan members Servers set interfaces ge-0/0/22 unit 0 family ethernet-switching vlan members Transit set interfaces ge-0/0/22 unit 0 family ethernet-switching vlan members Users set interfaces ge-0/0/22 unit 0 family ethernet-switching native-vlan-id default set interfaces ge-0/0/23 unit 0 description Router set interfaces ge-0/0/23 unit 0 family ethernet-switching vlan members Transit set interfaces ge-0/1/0 unit 0 family ethernet-switching set interfaces xe-0/1/0 unit 0 family ethernet-switching set interfaces ge-0/1/1 unit 0 family ethernet-switching set interfaces xe-0/1/1 unit 0 family ethernet-switching set interfaces ge-0/1/2 unit 0 family ethernet-switching set interfaces ge-0/1/3 unit 0 family ethernet-switching set interfaces ge-1/0/0 description "Test PC (J-Web as Desktop role)" set interfaces ge-1/0/0 mtu 1514 set interfaces ge-1/0/0 ether-options auto-negotiation set interfaces ge-1/0/0 ether-options no-flow-control set interfaces ge-1/0/0 ether-options link-mode automatic set interfaces ge-1/0/0 ether-options speed auto-negotiation set interfaces ge-1/0/0 unit 0 family ethernet-switching port-mode access set interfaces ge-1/0/0 unit 0 family ethernet-switching vlan members Users set interfaces ge-1/0/22 description "Backup Uplink to Cat2950" ---(more 52%)--- set interfaces ge-1/0/22 mtu 1514 set interfaces ge-1/0/22 ether-options auto-negotiation set interfaces ge-1/0/22 ether-options no-flow-control set interfaces ge-1/0/22 ether-options link-mode automatic set interfaces ge-1/0/22 ether-options speed auto-negotiation set interfaces ge-1/0/22 unit 0 family ethernet-switching port-mode trunk set interfaces ge-1/0/22 unit 0 family ethernet-switching vlan members Servers set interfaces ge-1/0/22 unit 0 family ethernet-switching vlan members Transit set interfaces ge-1/0/22 unit 0 family ethernet-switching vlan members Users set interfaces ge-1/0/22 unit 0 family ethernet-switching native-vlan-id default set interfaces ge-1/0/23 description "Backup Cisco router" set interfaces ge-1/0/23 mtu 1514 set interfaces ge-1/0/23 ether-options auto-negotiation set interfaces ge-1/0/23 ether-options no-flow-control set interfaces ge-1/0/23 ether-options link-mode automatic set interfaces ge-1/0/23 ether-options speed auto-negotiation set interfaces ge-1/0/23 unit 0 family ethernet-switching port-mode access set interfaces ge-1/0/23 unit 0 family ethernet-switching vlan members Transit set interfaces ae0 aggregated-ether-options minimum-links 1 set interfaces ae0 aggregated-ether-options link-speed 1g set interfaces ae0 aggregated-ether-options lacp active set interfaces ae0 aggregated-ether-options lacp periodic fast set interfaces ae0 unit 0 family ethernet-switching port-mode trunk set interfaces ae0 unit 0 family ethernet-switching vlan members all set interfaces ae1 aggregated-ether-options link-speed 100m set interfaces ae1 aggregated-ether-options lacp active set interfaces lo0 unit 10 family inet address 192.168.10.1/24 set interfaces me0 unit 0 family inet address 192.168.20.1/24 set interfaces vlan unit 2 description uservlan set interfaces vlan unit 2 family inet address 192.168.2.1/24 set interfaces vlan unit 3 description servervlan set interfaces vlan unit 3 family inet address 192.168.3.1/24 set interfaces vlan unit 100 description Transitvlan set interfaces vlan unit 100 family inet address 192.168.100.1/24 set interfaces vme unit 0 family inet address 192.168.30.1/24 set routing-options static route 10.1.1.1/32 next-hop 192.168.100.254 ---(more 79%)--- set routing-options static route 10.1.1.1/32 metric 200 set routing-options static route 0.0.0.0/0 next-hop 192.168.100.254 set routing-options static route 0.0.0.0/0 metric 150 set routing-options router-id 192.168.10.1 set protocols ospf area 0.0.0.0 interface ge-0/0/22.0 set protocols ospf area 0.0.0.0 interface lo0.10 set protocols ospf area 0.0.0.0 interface vlan.100 set protocols ospf area 0.0.0.0 interface vlan.2 set protocols ospf area 0.0.0.0 interface vlan.3 set protocols lldp interface all disable set protocols rstp interface ge-0/0/22.0 mode point-to-point set protocols rstp interface ge-1/0/0.0 edge set protocols rstp interface ge-1/0/22.0 mode point-to-point set protocols rstp interface ge-1/0/23.0 edge set ethernet-switching-options voip set vlans Servers vlan-id 3 set vlans Servers interface ge-0/0/13.0 set vlans Servers l3-interface vlan.3 set vlans Transit vlan-id 100 set vlans Transit interface ge-0/0/23.0 set vlans Transit l3-interface vlan.100 set vlans Users vlan-id 2 set vlans Users interface ge-0/0/0.0 set vlans Users l3-interface vlan.2 set vlans default vlan-id 1 set vlans mgmt set virtual-chassis member 1 mastership-priority 255 set poe interface all [edit] wide@LAB_EX-0# [edit] wide@LAB_EX-0# [edit] wide@LAB_EX-0# [edit] wide@LAB_EX-0# [edit] wide@LAB_EX-0# run show l ^ 'l' is ambiguous. Possible completions: l2circuit Show Layer 2 circuit information l2vpn Show Layer 2 VPN information lacp Show Link Aggregation Control Protocol information link-management Show link management information lldp Show Link Layer Discovery Protocol information log Show contents of log file [edit] wide@LAB_EX-0# run show lacp ? Possible completions: interfaces Show LACP interfaces information [edit] wide@LAB_EX-0# run show lacp interfaces Aggregated interface: ae0 LACP state: Role Exp Def Dist Col Syn Aggr Timeout Activity ge-0/0/14 Actor No No Yes Yes Yes Yes Fast Active ge-0/0/14 Partner No No Yes Yes Yes Yes Slow Active ge-0/0/15 Actor No No Yes Yes Yes Yes Fast Active ge-0/0/15 Partner No No Yes Yes Yes Yes Slow Active LACP protocol: Receive State Transmit State Mux State ge-0/0/14 Current Slow periodic Collecting distributing ge-0/0/15 Current Slow periodic Collecting distributing [edit] wide@LAB_EX-0# [edit] wide@LAB_EX-0# wide@LAB_EX-0# run show lacp interfaces ? Possible completions: <[Enter]> Execute this command Name of interface ge-0/0/0 ge-0/0/1 ge-0/0/2 ge-0/0/3 ge-0/0/4 ge-0/0/5 ge-0/0/6 ge-0/0/7 ge-0/0/8 ge-0/0/9 ge-0/0/10 ge-0/0/11 ge-0/0/12 ge-0/0/13 ge-0/0/14 ge-0/0/15 ge-0/0/16 ge-0/0/17 ge-0/0/18 ge-0/0/19 ge-0/0/20 ge-0/0/21 ge-0/0/22 Cisco Switch ge-0/0/23 ge-1/0/0 Test PC (J-Web as Desktop role) ge-1/0/1 ge-1/0/2 ge-1/0/3 ge-1/0/4 ge-1/0/5 ge-1/0/6 ge-1/0/7 ge-1/0/8 ---(more 66%)--- ge-1/0/9 ge-1/0/10 ge-1/0/11 ge-1/0/12 ge-1/0/13 ge-1/0/14 ge-1/0/15 ge-1/0/16 ge-1/0/17 ge-1/0/18 ge-1/0/19 ge-1/0/20 ge-1/0/21 ge-1/0/22 Backup Uplink to Cat2950 ge-1/0/23 Backup Cisco router ae0 ae1 | Pipe through a command [edit] wide@LAB_EX-0# run show lacp interfaces wide@LAB_EX-0# show | display set wide@LAB_EX-0# run show lacp interfaces wide@LAB_EX-0# show | display set wide@LAB_EX-0# run show lacp interfaces ? Possible completions: <[Enter]> Execute this command Name of interface ge-0/0/0 ge-0/0/1 ge-0/0/2 ge-0/0/3 ge-0/0/4 ge-0/0/5 ge-0/0/6 ge-0/0/7 ge-0/0/8 ge-0/0/9 ge-0/0/10 ge-0/0/11 ge-0/0/12 ge-0/0/13 ge-0/0/14 ge-0/0/15 ge-0/0/16 ge-0/0/17 ge-0/0/18 ge-0/0/19 ge-0/0/20 ge-0/0/21 ge-0/0/22 Cisco Switch ge-0/0/23 ge-1/0/0 Test PC (J-Web as Desktop role) ge-1/0/1 ge-1/0/2 ge-1/0/3 ge-1/0/4 ge-1/0/5 ge-1/0/6 ge-1/0/7 ge-1/0/8 ---(more 66%)---ò[abort] [edit] wide@LAB_EX-0#